EN 10028-2 13CrMo4-5 vs IS 11169 (Part 1) 40Cr4Mo3
Related Material — 67.6% match
based on chemical composition and mechanical property overlap.
EN 10028-2 13CrMo4-5 (EN 10028-2:2017) and IS 11169 (Part 1) 40Cr4Mo3 (IS 11169 (Part 1):2022) are both steel grades.
Both fall under the Alloy Steel category.
EN 10028-2 13CrMo4-5 is typically used for flat products for pressure purposes, while IS 11169 (Part 1) 40Cr4Mo3 is commonly used for cold heading and cold extrusion of parts that are quenched and tempered; the standard covers bars, wire rods and wires of 2 to 100 mm (clause 1.1, annex c).
EN 10028-2 13CrMo4-5 is defined under European Standard (EN), originating from Europe, while IS 11169 (Part 1) 40Cr4Mo3 is defined under Bureau of Indian Standards (IS), originating from India.
As per chemical composition, EN 10028-2 13CrMo4-5 vs IS 11169 (Part 1) 40Cr4Mo3 is a 67.6% match.
Mechanical property data is not available for both grades, so this factor could not be scored.
Combined, this makes them a related material overall at 67.6%.
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property
EN 10028-2 13CrMo4-5
IS 11169 (Part 1) 40Cr4Mo3
Tensile Strength
450-600 MPa
Not specified
Yield Strength
>=300 MPa
Not specified
Elongation
>=19%
Not specified
Condition
Usual delivery condition normalized and tempered (+NT), nominal thickness up to 16 mm; transverse direction, Yield Strength is ReH, Elongation is A
Not specified
Core Hardness (CH)
Not specified
>=48 HRC up to 28 mm
Hardness, annealed (+AC)
Not specified
<=200 HBW
Typical Applications
EN 10028-2 13CrMo4-5
Flat products for pressure purposes
IS 11169 (Part 1) 40Cr4Mo3
Cold heading and cold extrusion of parts that are quenched and tempered; the standard covers bars, wire rods and wires of 2 to 100 mm (clause 1.1, Annex C)
Key Differences
EN 10028-2 13CrMo4-5 specifies N which is not specified for IS 11169 (Part 1) 40Cr4Mo3.
Can EN 10028-2 13CrMo4-5 Be Substituted With IS 11169 (Part 1) 40Cr4Mo3?
EN 10028-2 13CrMo4-5 and IS 11169 (Part 1) 40Cr4Mo3 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
What is the difference between EN 10028-2 13CrMo4-5 and IS 11169 (Part 1) 40Cr4Mo3?
EN 10028-2 13CrMo4-5 specifies N which is not specified for IS 11169 (Part 1) 40Cr4Mo3.
Can EN 10028-2 13CrMo4-5 be substituted with IS 11169 (Part 1) 40Cr4Mo3?
EN 10028-2 13CrMo4-5 and IS 11169 (Part 1) 40Cr4Mo3 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.