Post Stock Login Register

EN 10084 22CrMoS3-5 vs EN 10028-2 13CrMo4-5

Close Alternative — 73.3% match based on chemical composition and mechanical property overlap.

EN 10084 22CrMoS3-5 (EN 10084:2008) and EN 10028-2 13CrMo4-5 (EN 10028-2:2017) are both steel grades. Both fall under the Alloy Steel category. EN 10084 22CrMoS3-5 is typically used for case hardened machine parts: carburized or carbonitrided, then hardened (clause 3.1), while EN 10028-2 13CrMo4-5 is commonly used for flat products for pressure purposes. EN 10084 22CrMoS3-5 is defined under European Standard (EN), originating from Europe, while EN 10028-2 13CrMo4-5 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10084 22CrMoS3-5 vs EN 10028-2 13CrMo4-5 is a 73.3% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 73.3%.

Frequently Compared With EN 10084 22CrMoS3-5:
IS 1570 (Part 7) 12Cr4Mo5H NF A35-565 100C6 IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 103Cr6 IS 4367 07Cr4Mo6 IS 1570 (Part 4) 07Cr4Mo6 UNI 11234 100Cr6 IS 1570 (Part 4) 105Cr5 IS 1570 (Part 4) 10Cr20Mo6 IS 1570 (Part 7) 10Cr36Mo10H IS 4367 10Cr9Mo10 IS 1570 (Part 4) 10Mo6
Match Breakdown
CHEMISTRY MATCH
73.3%
MECHANICAL MATCH
No shared data
OVERALL
73.3%
Specifications
Property EN 10084 22CrMoS3-5 EN 10028-2 13CrMo4-5
Standard EN 10084:2008 EN 10028-2:2017
Category Alloy Steel Alloy Steel
C (%) 0.19-0.24 0.08-0.18
Cr (%) 0.70-1.00 0.70-1.15
Mn (%) 0.70-1.00 0.40-1.00
Mo (%) 0.40-0.50 0.40-0.60
P (%) <=0.025 <=0.025
S (%) 0.020-0.040 <=0.010
Si (%) <=0.40 <=0.35
N (%) Not specified <=0.012
Cu (%) Not specified <=0.30
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10084 22CrMoS3-5 EN 10028-2 13CrMo4-5
Condition Soft annealed Usual delivery condition normalized and tempered (+NT), nominal thickness up to 16 mm; transverse direction, Yield Strength is ReH, Elongation is A
Hardenability +H band at 1.5 mm from the quenched end: 42 to 50 HRC Not specified
Hardness Soft annealed: 217 HB max Not specified
Tensile Strength Not specified 450-600 MPa
Yield Strength Not specified >=300 MPa
Elongation Not specified >=19%
Typical Applications
EN 10084 22CrMoS3-5
Case hardened machine parts: carburized or carbonitrided, then hardened (clause 3.1)
EN 10028-2 13CrMo4-5
Flat products for pressure purposes
Key Differences
Can EN 10084 22CrMoS3-5 Be Substituted With EN 10028-2 13CrMo4-5?
EN 10084 22CrMoS3-5 and EN 10028-2 13CrMo4-5 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
EN 10084 22CrMoS3-5
0 active listings and RFQs →
EN 10028-2 13CrMo4-5
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10084 22CrMoS3-5 and EN 10028-2 13CrMo4-5?
EN 10028-2 13CrMo4-5 specifies N, Cu which are not specified for EN 10084 22CrMoS3-5.
Can EN 10084 22CrMoS3-5 be substituted with EN 10028-2 13CrMo4-5?
EN 10084 22CrMoS3-5 and EN 10028-2 13CrMo4-5 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.