Post Stock Login Register

EN 10088-1 X1CrNiMoAlTi12-11-2 vs GOST 5632 08X18H10

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

EN 10088-1 X1CrNiMoAlTi12-11-2 (EN 10088-1:2023) and GOST 5632 08X18H10 (GOST 5632-2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-1 X1CrNiMoAlTi12-11-2 is defined under European Standard (EN) (Europe).

As per chemical composition, EN 10088-1 X1CrNiMoAlTi12-11-2 vs GOST 5632 08X18H10 is a 49% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With EN 10088-1 X1CrNiMoAlTi12-11-2:
ASTM A959 .- GB/T 3280 06Cr19Ni10 EN 10088-1 1.4301 EN 10088-1 1.4401 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12Ni2Mo GOST 5632 06Kh23N28 EN 10088-1 1.4006 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr13H
Match Breakdown
CHEMISTRY MATCH
49%
MECHANICAL MATCH
No shared data
OVERALL
35%
Specifications
Property EN 10088-1 X1CrNiMoAlTi12-11-2 GOST 5632 08X18H10
Standard EN 10088-1:2023 GOST 5632-2014
Category Stainless Steel Stainless Steel
C (%) <=0.015 ≤0.08
Si (%) <=0.10 ≤0.80
Mn (%) <=0.10 ≤2.00
P (%) <=0.010 ≤0.035
S (%) <=0.005 ≤0.020
Cr (%) 11.0-12.5 17.0–19.0
Mo (%) 1.75-2.25 Not specified
Ni (%) 10.2-11.3 9.0–11.0
Al (%) 1.35-1.75 Not specified
Ti (%) 0.20-0.50 Not specified
N (%) <=0.010 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X1CrNiMoAlTi12-11-2 GOST 5632 08X18H10
Tensile Strength Not specified ≥520 MPa
Yield Strength Not specified ≥205 MPa
Elongation Not specified ≥40%
Typical Applications
EN 10088-1 X1CrNiMoAlTi12-11-2
Not documented
GOST 5632 08X18H10
Chemical equipment, food processing, general corrosion resistant applications
Key Differences
Can EN 10088-1 X1CrNiMoAlTi12-11-2 Be Substituted With GOST 5632 08X18H10?
EN 10088-1 X1CrNiMoAlTi12-11-2 and GOST 5632 08X18H10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN 10088-1 X1CrNiMoAlTi12-11-2
No active listings currently.
GOST 5632 08X18H10
Sheet → (2 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2500–2700 mm (98.43–106.3 in)
On M-EX Right Now
EN 10088-1 X1CrNiMoAlTi12-11-2
0 active listings and RFQs →
GOST 5632 08X18H10
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X1CrNiMoAlTi12-11-2 and GOST 5632 08X18H10?
EN 10088-1 X1CrNiMoAlTi12-11-2 specifies Mo, Al, Ti, N which are not specified for GOST 5632 08X18H10.
Can EN 10088-1 X1CrNiMoAlTi12-11-2 be substituted with GOST 5632 08X18H10?
EN 10088-1 X1CrNiMoAlTi12-11-2 and GOST 5632 08X18H10 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.