Post Stock Login Register

EN 10088-1 X2CrMnNiTi12 vs EN 10088-2 X2CrMnNiTi12

Strong Match — 95.2% match based on chemical composition and mechanical property overlap.

EN 10088-1 X2CrMnNiTi12 (EN 10088-1:2023) and EN 10088-2 X2CrMnNiTi12 (EN 10088-2:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-1 X2CrMnNiTi12 is defined under European Standard (EN), originating from Europe, while EN 10088-2 X2CrMnNiTi12 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-1 X2CrMnNiTi12 vs EN 10088-2 X2CrMnNiTi12 is a 95.2% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 95.2%.

Frequently Compared With EN 10088-1 X2CrMnNiTi12:
GB/T 3280 06Cr19Ni10 EN 10088-1 1.4301 EN 10088-1 1.4845 ASTM A959 .- GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4401 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
95.2%
MECHANICAL MATCH
No shared data
OVERALL
95.2%
Specifications
Property EN 10088-1 X2CrMnNiTi12 EN 10088-2 X2CrMnNiTi12
Standard EN 10088-1:2023 EN 10088-2:2014
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.030
Si (%) <=1.00 <=1.00
Mn (%) 1.00-2.50 1.00-2.50
P (%) <=0.040 <=0.040
S (%) <=0.015 <=0.015
Cr (%) 11.0-13.0 11.0-13.0
Ni (%) 0.30-1.00 0.30-1.00
N (%) <=0.025 <=0.025
Ti (%) Not specified <=0.35
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X2CrMnNiTi12 EN 10088-2 X2CrMnNiTi12
Tensile Strength Not specified 500-650 MPa
Condition Not specified Annealed (+A), hot rolled strip, up to 10 mm thick; Yield Strength is Rp0.2 (transverse; longitudinal not given); Elongation is A80 (under 3 mm) or A (3 mm and over)
Elongation Not specified >=20%
Yield Strength Not specified >=375 MPa
Typical Applications
EN 10088-1 X2CrMnNiTi12
Not documented
EN 10088-2 X2CrMnNiTi12
General purposes, hot or cold rolled sheet/plate and strip
Key Differences
Can EN 10088-1 X2CrMnNiTi12 Be Substituted With EN 10088-2 X2CrMnNiTi12?
EN 10088-1 X2CrMnNiTi12 and EN 10088-2 X2CrMnNiTi12 overlap closely enough on chemistry and mechanical properties that EN 10088-2 X2CrMnNiTi12 is often considered as a substitute for EN 10088-1 X2CrMnNiTi12 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
On M-EX Right Now
EN 10088-1 X2CrMnNiTi12
0 active listings and RFQs →
EN 10088-2 X2CrMnNiTi12
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X2CrMnNiTi12 and EN 10088-2 X2CrMnNiTi12?
EN 10088-2 X2CrMnNiTi12 specifies Ti which is not specified for EN 10088-1 X2CrMnNiTi12.
Can EN 10088-1 X2CrMnNiTi12 be substituted with EN 10088-2 X2CrMnNiTi12?
EN 10088-1 X2CrMnNiTi12 and EN 10088-2 X2CrMnNiTi12 overlap closely enough on chemistry and mechanical properties that EN 10088-2 X2CrMnNiTi12 is often considered as a substitute for EN 10088-1 X2CrMnNiTi12 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.