Post Stock Login Register

EN 10088-1 X3CrNiCu18-9-4 vs GOST 5632 08X18H10

Close Alternative — 76.5% match based on chemical composition and mechanical property overlap.

EN 10088-1 X3CrNiCu18-9-4 (EN 10088-1:2023) and GOST 5632 08X18H10 (GOST 5632-2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-1 X3CrNiCu18-9-4 is defined under European Standard (EN) (Europe).

As per chemical composition, EN 10088-1 X3CrNiCu18-9-4 vs GOST 5632 08X18H10 is a 76.5% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 76.5%.

Frequently Compared With EN 10088-1 X3CrNiCu18-9-4:
EN 10088-1 1.4301 ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 EN 10088-1 1.4006 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo IS 1570 (Part 7) 12Cr13H IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH
Match Breakdown
CHEMISTRY MATCH
76.5%
MECHANICAL MATCH
No shared data
OVERALL
76.5%
Specifications
Property EN 10088-1 X3CrNiCu18-9-4 GOST 5632 08X18H10
Standard EN 10088-1:2023 GOST 5632-2014
Category Stainless Steel Stainless Steel
C (%) <=0.04 ≤0.08
Si (%) <=1.00 ≤0.80
Mn (%) <=2.00 ≤2.00
P (%) <=0.045 ≤0.035
S (%) <=0.015 ≤0.020
Cr (%) 17.0-19.0 17.0–19.0
Ni (%) 8.5-10.5 9.0–11.0
N (%) <=0.10 Not specified
Cu (%) 3.00-4.0 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X3CrNiCu18-9-4 GOST 5632 08X18H10
Tensile Strength Not specified ≥520 MPa
Yield Strength Not specified ≥205 MPa
Elongation Not specified ≥40%
Typical Applications
EN 10088-1 X3CrNiCu18-9-4
Not documented
GOST 5632 08X18H10
Chemical equipment, food processing, general corrosion resistant applications
Key Differences
Can EN 10088-1 X3CrNiCu18-9-4 Be Substituted With GOST 5632 08X18H10?
EN 10088-1 X3CrNiCu18-9-4 and GOST 5632 08X18H10 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
EN 10088-1 X3CrNiCu18-9-4
No active listings currently.
GOST 5632 08X18H10
Sheet → (2 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2500–2700 mm (98.43–106.3 in)
On M-EX Right Now
EN 10088-1 X3CrNiCu18-9-4
0 active listings and RFQs →
GOST 5632 08X18H10
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X3CrNiCu18-9-4 and GOST 5632 08X18H10?
EN 10088-1 X3CrNiCu18-9-4 specifies N, Cu which are not specified for GOST 5632 08X18H10.
Can EN 10088-1 X3CrNiCu18-9-4 be substituted with GOST 5632 08X18H10?
EN 10088-1 X3CrNiCu18-9-4 and GOST 5632 08X18H10 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.