Post Stock Login Register

EN 10088-2 X2CrNbTi20 vs EN 10088-1 X2CrTiNb18

Close Alternative — 82.1% match based on chemical composition and mechanical property overlap.

EN 10088-2 X2CrNbTi20 (EN 10088-2:2014) and EN 10088-1 X2CrTiNb18 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-2 X2CrNbTi20 is defined under European Standard (EN), originating from Europe, while EN 10088-1 X2CrTiNb18 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-2 X2CrNbTi20 vs EN 10088-1 X2CrTiNb18 is a 82.1% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 82.1%.

Frequently Compared With EN 10088-2 X2CrNbTi20:
ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
82.1%
MECHANICAL MATCH
No shared data
OVERALL
82.1%
Specifications
Property EN 10088-2 X2CrNbTi20 EN 10088-1 X2CrTiNb18
Standard EN 10088-2:2014 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.030
Si (%) <=1.00 <=1.00
Mn (%) <=1.00 <=1.00
P (%) <=0.040 <=0.040
S (%) <=0.015 <=0.015
Cr (%) 18.5-20.5 17.5-18.5
N (%) <=0.030 Not specified
Nb (%) <=1.00 Not specified
Ti (%) <=0.80 0.10-0.60
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-2 X2CrNbTi20 EN 10088-1 X2CrTiNb18
Tensile Strength 430-630 MPa Not specified
Condition Annealed (+A), cold rolled strip, up to 8 mm thick; Elongation is A80 (under 3 mm) or A (3 mm and over), longitudinal and transverse Not specified
Yield Strength >=230 MPa Not specified
Elongation >=18% Not specified
Typical Applications
EN 10088-2 X2CrNbTi20
General purposes, hot or cold rolled sheet/plate and strip
EN 10088-1 X2CrTiNb18
Not documented
Key Differences
Can EN 10088-2 X2CrNbTi20 Be Substituted With EN 10088-1 X2CrTiNb18?
EN 10088-2 X2CrNbTi20 and EN 10088-1 X2CrTiNb18 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
EN 10088-2 X2CrNbTi20
0 active listings and RFQs →
EN 10088-1 X2CrTiNb18
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-2 X2CrNbTi20 and EN 10088-1 X2CrTiNb18?
EN 10088-2 X2CrNbTi20 specifies N, Nb which are not specified for EN 10088-1 X2CrTiNb18.
Can EN 10088-2 X2CrNbTi20 be substituted with EN 10088-1 X2CrTiNb18?
EN 10088-2 X2CrNbTi20 and EN 10088-1 X2CrTiNb18 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.