Post Stock Login Register

EN 10088-2 X2CrNiMoN25-7-4 vs EN 10088-2 X2CrNiMoCuN25-6-3

Strong Match — 93% match based on chemical composition and mechanical property overlap.

EN 10088-2 X2CrNiMoN25-7-4 (EN 10088-2:2014) and EN 10088-2 X2CrNiMoCuN25-6-3 (EN 10088-2:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-2 X2CrNiMoN25-7-4 is typically used for general purposes, hot or cold rolled sheet/plate and strip, while EN 10088-2 X2CrNiMoCuN25-6-3 is commonly used for general purposes, hot or cold rolled sheet/plate and strip. EN 10088-2 X2CrNiMoN25-7-4 is defined under European Standard (EN), originating from Europe, while EN 10088-2 X2CrNiMoCuN25-6-3 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-2 X2CrNiMoN25-7-4 vs EN 10088-2 X2CrNiMoCuN25-6-3 is a 89.4% match. As per mechanical properties, the match is 100%. Combined, this makes them a strong match overall at 93%.

Frequently Compared With EN 10088-2 X2CrNiMoN25-7-4:
ASTM A959 2507 GB/T 3280 06Cr19Ni10 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH ASTM A959 .- GOST 5632 06Kh23N28 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH
Match Breakdown
CHEMISTRY MATCH
89.4%
MECHANICAL MATCH
100%
OVERALL
93%
Specifications
Property EN 10088-2 X2CrNiMoN25-7-4 EN 10088-2 X2CrNiMoCuN25-6-3
Standard EN 10088-2:2014 EN 10088-2:2014
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.030
Si (%) <=1.00 <=0.70
Mn (%) <=2.00 <=2.00
P (%) <=0.035 <=0.035
S (%) <=0.015 <=0.015
Cr (%) 24.0-26.0 24.0-26.0
Mo (%) 3.0-4.5 3.0-4.0
Ni (%) 6.0-8.0 6.0-8.0
N (%) 0.24-0.35 0.20-0.30
Cu (%) Not specified 1.00-2.50
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-2 X2CrNiMoN25-7-4 EN 10088-2 X2CrNiMoCuN25-6-3
Tensile Strength 750-1000 MPa 750-1000 MPa
Yield Strength >=550 MPa >=550 MPa
Elongation >=20% >=20%
Condition Solution annealed (+AT), cold rolled strip, up to 8 mm thick; Yield Strength is Rp0.2 (transverse), Elongation is A80 for under 3 mm thick Solution annealed (+AT), cold rolled strip, up to 8 mm thick; Yield Strength is Rp0.2 (transverse), Elongation is A80 for under 3 mm thick
Typical Applications
EN 10088-2 X2CrNiMoN25-7-4
General purposes, hot or cold rolled sheet/plate and strip
EN 10088-2 X2CrNiMoCuN25-6-3
General purposes, hot or cold rolled sheet/plate and strip
Key Differences
Can EN 10088-2 X2CrNiMoN25-7-4 Be Substituted With EN 10088-2 X2CrNiMoCuN25-6-3?
EN 10088-2 X2CrNiMoN25-7-4 and EN 10088-2 X2CrNiMoCuN25-6-3 overlap closely enough on chemistry and mechanical properties that EN 10088-2 X2CrNiMoCuN25-6-3 is often considered as a substitute for EN 10088-2 X2CrNiMoN25-7-4 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
On M-EX Right Now
EN 10088-2 X2CrNiMoN25-7-4
0 active listings and RFQs →
EN 10088-2 X2CrNiMoCuN25-6-3
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-2 X2CrNiMoN25-7-4 and EN 10088-2 X2CrNiMoCuN25-6-3?
EN 10088-2 X2CrNiMoCuN25-6-3 specifies Cu which is not specified for EN 10088-2 X2CrNiMoN25-7-4.
Can EN 10088-2 X2CrNiMoN25-7-4 be substituted with EN 10088-2 X2CrNiMoCuN25-6-3?
EN 10088-2 X2CrNiMoN25-7-4 and EN 10088-2 X2CrNiMoCuN25-6-3 overlap closely enough on chemistry and mechanical properties that EN 10088-2 X2CrNiMoCuN25-6-3 is often considered as a substitute for EN 10088-2 X2CrNiMoN25-7-4 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.