Post Stock Login Register

EN 10088-2 X50CrMoV15 vs EN 10088-1 1.4301

Minimal Match — 32% match based on chemical composition and mechanical property overlap.

EN 10088-2 X50CrMoV15 (EN 10088-2:2014) and EN 10088-1 1.4301 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-2 X50CrMoV15 is typically used for general purposes, hot or cold rolled sheet/plate and strip, while EN 10088-1 1.4301 is commonly used for food equipment, chemical vessels, architectural, kitchenware. EN 10088-2 X50CrMoV15 is defined under European Standard (EN), originating from Europe, while EN 10088-1 1.4301 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-2 X50CrMoV15 vs EN 10088-1 1.4301 is a 48.1% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 32%.

Frequently Compared With EN 10088-2 X50CrMoV15:
ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo EN 10088-1 1.4006 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr13H
Match Breakdown
CHEMISTRY MATCH
48.1%
MECHANICAL MATCH
0%
OVERALL
32%
Specifications
Property EN 10088-2 X50CrMoV15 EN 10088-1 1.4301
Standard EN 10088-2:2014 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) 0.45-0.55 ≤0.07
Si (%) <=1.00 ≤1.00
Mn (%) <=1.00 ≤2.00
P (%) <=0.040 ≤0.045
S (%) <=0.015 ≤0.030
Cr (%) 14.0-15.0 17.5–19.5
Mo (%) 0.50-0.80 Not specified
V (%) 0.10-0.20 Not specified
Ni (%) Not specified 8.0–10.5
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-2 X50CrMoV15 EN 10088-1 1.4301
Tensile Strength <=850 MPa ≥520 MPa
Elongation >=12% ≥45%
Hardness <=280 HB ≤215 HB
Condition Annealed (+A), cold rolled strip, up to 8 mm thick Not specified
Yield Strength Not specified ≥210 MPa
Typical Applications
EN 10088-2 X50CrMoV15
General purposes, hot or cold rolled sheet/plate and strip
EN 10088-1 1.4301
Food equipment, chemical vessels, architectural, kitchenware
Key Differences
Can EN 10088-2 X50CrMoV15 Be Substituted With EN 10088-1 1.4301?
EN 10088-2 X50CrMoV15 and EN 10088-1 1.4301 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN 10088-2 X50CrMoV15
No active listings currently.
EN 10088-1 1.4301
Sheet → (3 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2500–3300 mm (98.43–129.92 in)
On M-EX Right Now
EN 10088-2 X50CrMoV15
0 active listings and RFQs →
EN 10088-1 1.4301
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-2 X50CrMoV15 and EN 10088-1 1.4301?
EN 10088-2 X50CrMoV15 specifies Mo, V which are not specified for EN 10088-1 1.4301. EN 10088-1 1.4301 specifies Ni which is not specified for EN 10088-2 X50CrMoV15.
Can EN 10088-2 X50CrMoV15 be substituted with EN 10088-1 1.4301?
EN 10088-2 X50CrMoV15 and EN 10088-1 1.4301 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.