Post Stock Login Register

EN 10088-3 X12CrMnNiN17-7-5 vs EN 10088-1 X12CrMnNiN18-9-5

Strong Match — 85.6% match based on chemical composition and mechanical property overlap.

EN 10088-3 X12CrMnNiN17-7-5 (EN 10088-3:2014) and EN 10088-1 X12CrMnNiN18-9-5 (EN 10088-1:2023) are both steel grades. Both fall under the Stainless Steel category. EN 10088-3 X12CrMnNiN17-7-5 is defined under European Standard (EN), originating from Europe, while EN 10088-1 X12CrMnNiN18-9-5 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-3 X12CrMnNiN17-7-5 vs EN 10088-1 X12CrMnNiN18-9-5 is a 85.6% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 85.6%.

Frequently Compared With EN 10088-3 X12CrMnNiN17-7-5:
ASTM A959 201 GB/T 3280 06Cr19Ni10 ASTM A959 .- EN 10088-1 1.4301 IS 1570 (Part 7) 11Cr17Ni13W3TiH ASTM A959 202 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr12MoH
Match Breakdown
CHEMISTRY MATCH
85.6%
MECHANICAL MATCH
No shared data
OVERALL
85.6%
Specifications
Property EN 10088-3 X12CrMnNiN17-7-5 EN 10088-1 X12CrMnNiN18-9-5
Standard EN 10088-3:2014 EN 10088-1:2023
Category Stainless Steel Stainless Steel
C (%) <=0.15 <=0.15
Si (%) <=1.00 <=1.00
Mn (%) 5.5-7.5 7.5-10.5
P (%) <=0.045 <=0.045
S (%) <=0.015 <=0.015
Cr (%) 16.0-18.0 17.0-19.0
Ni (%) 3.5-5.5 4.0-6.0
N (%) 0.05-0.25 0.05-0.25
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-3 X12CrMnNiN17-7-5 EN 10088-1 X12CrMnNiN18-9-5
Tensile Strength 680-880 MPa Not specified
Yield Strength >=230 MPa Not specified
Elongation >=40% Not specified
Hardness <=260 HB Not specified
Condition Solution annealed (+AT), conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 160 mm; Yield Strength is Rp0.2, Elongation is A (longitudinal), hardness for guidance only Not specified
Typical Applications
EN 10088-3 X12CrMnNiN17-7-5
General purposes, semi-finished products, bars, rods, wire, sections and bright products
EN 10088-1 X12CrMnNiN18-9-5
Not documented
Can EN 10088-3 X12CrMnNiN17-7-5 Be Substituted With EN 10088-1 X12CrMnNiN18-9-5?
EN 10088-3 X12CrMnNiN17-7-5 and EN 10088-1 X12CrMnNiN18-9-5 overlap closely enough on chemistry and mechanical properties that EN 10088-1 X12CrMnNiN18-9-5 is often considered as a substitute for EN 10088-3 X12CrMnNiN17-7-5 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
On M-EX Right Now
EN 10088-3 X12CrMnNiN17-7-5
0 active listings and RFQs →
EN 10088-1 X12CrMnNiN18-9-5
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-3 X12CrMnNiN17-7-5 and EN 10088-1 X12CrMnNiN18-9-5?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can EN 10088-3 X12CrMnNiN17-7-5 be substituted with EN 10088-1 X12CrMnNiN18-9-5?
EN 10088-3 X12CrMnNiN17-7-5 and EN 10088-1 X12CrMnNiN18-9-5 overlap closely enough on chemistry and mechanical properties that EN 10088-1 X12CrMnNiN18-9-5 is often considered as a substitute for EN 10088-3 X12CrMnNiN17-7-5 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.