Post Stock Login Register

EN 10088-3 X15Cr13 vs ASTM A959 416Se

Strong Match — 89.7% match based on chemical composition and mechanical property overlap.

EN 10088-3 X15Cr13 (EN 10088-3:2014) and ASTM A959 416Se (ASTM A959:2011) are both steel grades. Both fall under the Stainless Steel category. EN 10088-3 X15Cr13 is typically used for general purposes, semi-finished products, bars, rods, wire, sections and bright products, while ASTM A959 416Se is commonly used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1). EN 10088-3 X15Cr13 is defined under European Standard (EN), originating from Europe, while ASTM A959 416Se is defined under ASTM International, originating from United States.

As per chemical composition, EN 10088-3 X15Cr13 vs ASTM A959 416Se is a 89.7% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 89.7%.

Frequently Compared With EN 10088-3 X15Cr13:
ASTM A959 .- GB/T 3280 06Cr19Ni10 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoVH GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
89.7%
MECHANICAL MATCH
No shared data
OVERALL
89.7%
Specifications
Property EN 10088-3 X15Cr13 ASTM A959 416Se
Standard EN 10088-3:2014 ASTM A959:2011
Category Stainless Steel Stainless Steel
C (%) 0.12-0.17 <=0.15
Si (%) <=1.00 <=1.00
Mn (%) <=1.00 <=1.25
P (%) <=0.040 <=0.06
S (%) <=0.030 <=0.06
Cr (%) 12.0-14.0 12.0-14.0
Se (%) Not specified >=0.15
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-3 X15Cr13 ASTM A959 416Se
Tensile Strength <=730 MPa Not specified
Hardness <=220 HB Not specified
Condition Annealed (+A), conditions 1C, 1E, 1D, 1X, 1G and 2D, size range not stated; hardness for guidance only Not specified
Typical Applications
EN 10088-3 X15Cr13
General purposes, semi-finished products, bars, rods, wire, sections and bright products
ASTM A959 416Se
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
Key Differences
Can EN 10088-3 X15Cr13 Be Substituted With ASTM A959 416Se?
EN 10088-3 X15Cr13 and ASTM A959 416Se overlap closely enough on chemistry and mechanical properties that ASTM A959 416Se is often considered as a substitute for EN 10088-3 X15Cr13 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
On M-EX Right Now
EN 10088-3 X15Cr13
0 active listings and RFQs →
ASTM A959 416Se
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-3 X15Cr13 and ASTM A959 416Se?
ASTM A959 416Se specifies Se which is not specified for EN 10088-3 X15Cr13.
Can EN 10088-3 X15Cr13 be substituted with ASTM A959 416Se?
EN 10088-3 X15Cr13 and ASTM A959 416Se overlap closely enough on chemistry and mechanical properties that ASTM A959 416Se is often considered as a substitute for EN 10088-3 X15Cr13 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.