Post Stock Login Register

EN 10088-3 X2CrNiMo18-15-4 vs EN 10088-1 X2CrNiMo18-15-4

Strong Match — 98.6% match based on chemical composition and mechanical property overlap.

EN 10088-3 X2CrNiMo18-15-4 (EN 10088-3:2014) and EN 10088-1 X2CrNiMo18-15-4 (EN 10088-1:2023) are both steel grades. Both fall under the Stainless Steel category. EN 10088-3 X2CrNiMo18-15-4 is defined under European Standard (EN), originating from Europe, while EN 10088-1 X2CrNiMo18-15-4 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-3 X2CrNiMo18-15-4 vs EN 10088-1 X2CrNiMo18-15-4 is a 98.6% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 98.6%.

Frequently Compared With EN 10088-3 X2CrNiMo18-15-4:
EN 10088-1 1.4006 ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
98.6%
MECHANICAL MATCH
No shared data
OVERALL
98.6%
Specifications
Property EN 10088-3 X2CrNiMo18-15-4 EN 10088-1 X2CrNiMo18-15-4
Standard EN 10088-3:2014 EN 10088-1:2023
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.030
Si (%) <=1.00 <=1.00
Mn (%) <=2.00 <=2.00
P (%) <=0.045 <=0.045
S (%) <=0.030 <=0.015
Cr (%) 17.5-19.5 17.5-19.5
Mo (%) 3.0-4.0 3.00-4.0
Ni (%) 13.0-16.0 13.0-16.0
N (%) <=0.10 <=0.10
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-3 X2CrNiMo18-15-4 EN 10088-1 X2CrNiMo18-15-4
Tensile Strength 500-700 MPa Not specified
Yield Strength >=200 MPa Not specified
Elongation >=40% Not specified
Hardness <=215 HB Not specified
Condition Solution annealed (+AT), conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 160 mm; Yield Strength is Rp0.2, Elongation is A (longitudinal), hardness for guidance only Not specified
Typical Applications
EN 10088-3 X2CrNiMo18-15-4
General purposes, semi-finished products, bars, rods, wire, sections and bright products
EN 10088-1 X2CrNiMo18-15-4
Not documented
Can EN 10088-3 X2CrNiMo18-15-4 Be Substituted With EN 10088-1 X2CrNiMo18-15-4?
EN 10088-3 X2CrNiMo18-15-4 and EN 10088-1 X2CrNiMo18-15-4 overlap closely enough on chemistry and mechanical properties that EN 10088-1 X2CrNiMo18-15-4 is often considered as a substitute for EN 10088-3 X2CrNiMo18-15-4 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
On M-EX Right Now
EN 10088-3 X2CrNiMo18-15-4
0 active listings and RFQs →
EN 10088-1 X2CrNiMo18-15-4
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-3 X2CrNiMo18-15-4 and EN 10088-1 X2CrNiMo18-15-4?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can EN 10088-3 X2CrNiMo18-15-4 be substituted with EN 10088-1 X2CrNiMo18-15-4?
EN 10088-3 X2CrNiMo18-15-4 and EN 10088-1 X2CrNiMo18-15-4 overlap closely enough on chemistry and mechanical properties that EN 10088-1 X2CrNiMo18-15-4 is often considered as a substitute for EN 10088-3 X2CrNiMo18-15-4 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.