EN 10088-3 X5CrNiCuNb16-4 vs EN 10088-3 X5CrNiMoCuNb14-5
Related Material — 69.9% match
based on chemical composition and mechanical property overlap.
EN 10088-3 X5CrNiCuNb16-4 (EN 10088-3:2014) and EN 10088-3 X5CrNiMoCuNb14-5 (EN 10088-3:2014) are both steel grades.
Both fall under the Stainless Steel category.
EN 10088-3 X5CrNiCuNb16-4 is typically used for general purposes, semi-finished products, bars, rods, wire, sections and bright products, while EN 10088-3 X5CrNiMoCuNb14-5 is commonly used for general purposes, semi-finished products, bars, rods, wire, sections and bright products.
EN 10088-3 X5CrNiCuNb16-4 is defined under European Standard (EN), originating from Europe, while EN 10088-3 X5CrNiMoCuNb14-5 is defined under European Standard (EN), originating from Europe.
As per chemical composition, EN 10088-3 X5CrNiCuNb16-4 vs EN 10088-3 X5CrNiMoCuNb14-5 is a 66.2% match.
As per mechanical properties, the match is 100%.
Combined, this makes them a related material overall at 69.9%.
Frequently Compared With EN 10088-3 X5CrNiCuNb16-4:
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property
EN 10088-3 X5CrNiCuNb16-4
EN 10088-3 X5CrNiMoCuNb14-5
Tensile Strength
<=1200 MPa
<=1200 MPa
Hardness
<=360 HB
<=360 HB
Condition
Solution annealed (+AT), conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 100 mm; hardness for guidance only
Solution annealed (+AT), conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 100 mm; hardness for guidance only
Typical Applications
EN 10088-3 X5CrNiCuNb16-4
General purposes, semi-finished products, bars, rods, wire, sections and bright products
EN 10088-3 X5CrNiMoCuNb14-5
General purposes, semi-finished products, bars, rods, wire, sections and bright products
Can EN 10088-3 X5CrNiCuNb16-4 Be Substituted With EN 10088-3 X5CrNiMoCuNb14-5?
EN 10088-3 X5CrNiCuNb16-4 and EN 10088-3 X5CrNiMoCuNb14-5 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
What is the difference between EN 10088-3 X5CrNiCuNb16-4 and EN 10088-3 X5CrNiMoCuNb14-5?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can EN 10088-3 X5CrNiCuNb16-4 be substituted with EN 10088-3 X5CrNiMoCuNb14-5?
EN 10088-3 X5CrNiCuNb16-4 and EN 10088-3 X5CrNiMoCuNb14-5 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.