Post Stock Login Register

EN 10088-3 X6CrMnNiCuN18-12-4-2 vs EN 10088-1 X8CrMnNiN18-9-5

Related Material — 66.7% match based on chemical composition and mechanical property overlap.

EN 10088-3 X6CrMnNiCuN18-12-4-2 (EN 10088-3:2014) and EN 10088-1 X8CrMnNiN18-9-5 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-3 X6CrMnNiCuN18-12-4-2 is defined under European Standard (EN), originating from Europe, while EN 10088-1 X8CrMnNiN18-9-5 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10088-3 X6CrMnNiCuN18-12-4-2 vs EN 10088-1 X8CrMnNiN18-9-5 is a 66.7% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 66.7%.

Frequently Compared With EN 10088-3 X6CrMnNiCuN18-12-4-2:
ASTM A959 .- GOST 5632 08X18H10 GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
66.7%
MECHANICAL MATCH
No shared data
OVERALL
66.7%
Specifications
Property EN 10088-3 X6CrMnNiCuN18-12-4-2 EN 10088-1 X8CrMnNiN18-9-5
Standard EN 10088-3:2014 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) 0.02-0.10 0.05-0.10
Si (%) <=1.00 0.30-0.60
Mn (%) 10.5-12.5 9.0-10.0
P (%) <=0.050 <=0.035
S (%) <=0.015 <=0.030
Cr (%) 17.0-19.0 17.5-18.5
Mo (%) <=0.50 <=0.50
Ni (%) 3.5-4.5 5.0-6.0
N (%) 0.20-0.30 0.25-0.32
Cu (%) 1.50-3.00 <=0.40
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-3 X6CrMnNiCuN18-12-4-2 EN 10088-1 X8CrMnNiN18-9-5
Tensile Strength 650-850 MPa Not specified
Yield Strength >=380 MPa Not specified
Elongation >=30% Not specified
Hardness <=260 HB Not specified
Condition Solution annealed (+AT), conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 8 mm; Yield Strength is Rp0.2, Elongation is A (longitudinal), hardness for guidance only Not specified
Typical Applications
EN 10088-3 X6CrMnNiCuN18-12-4-2
General purposes, semi-finished products, bars, rods, wire, sections and bright products
EN 10088-1 X8CrMnNiN18-9-5
Not documented
Can EN 10088-3 X6CrMnNiCuN18-12-4-2 Be Substituted With EN 10088-1 X8CrMnNiN18-9-5?
EN 10088-3 X6CrMnNiCuN18-12-4-2 and EN 10088-1 X8CrMnNiN18-9-5 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
EN 10088-3 X6CrMnNiCuN18-12-4-2
0 active listings and RFQs →
EN 10088-1 X8CrMnNiN18-9-5
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-3 X6CrMnNiCuN18-12-4-2 and EN 10088-1 X8CrMnNiN18-9-5?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can EN 10088-3 X6CrMnNiCuN18-12-4-2 be substituted with EN 10088-1 X8CrMnNiN18-9-5?
EN 10088-3 X6CrMnNiCuN18-12-4-2 and EN 10088-1 X8CrMnNiN18-9-5 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.