Post Stock Login Register

EN 10089 55Si7 vs EN 10089 50CrV4

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

EN 10089 55Si7 (EN 10089:2002) and EN 10089 50CrV4 (EN 10089:2002) are both steel grades. Both fall under the Spring Steel category. EN 10089 55Si7 is typically used for leaf springs, coil springs, torsion bars, while EN 10089 50CrV4 is commonly used for valve springs, high duty coil springs, hand tools. EN 10089 55Si7 is defined under European Standard (EN), originating from Europe, while EN 10089 50CrV4 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10089 55Si7 vs EN 10089 50CrV4 is a 70.8% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With EN 10089 55Si7:
EN 10083-3 51CrV4 EN 10089 55Cr3 GB/T 1222 55CrMnA IS 1570 (Part 4) 55Si7 IS 1570 (Part 4) 60Si7 IS 1570 (Part 4) 65Si7 IS 4367 55Si7 IS 5517 55Cr3 BS 970 EN42B BS 970 EN42
Other Spring Steel Grades to Compare With EN 10089 55Si7:
IS 3195 113C6 IS 3431 50Cr4V2
Match Breakdown
CHEMISTRY MATCH
70.8%
MECHANICAL MATCH
0%
OVERALL
35%
Specifications
Property EN 10089 55Si7 EN 10089 50CrV4
Standard EN 10089:2002 EN 10089:2002
Category Spring Steel Spring Steel
C (%) 0.51–0.59 0.47–0.55
Si (%) 1.50–2.00 0.15–0.35
Mn (%) 0.70–1.00 0.70–1.10
S (%) ≤0.040 Not specified
P (%) ≤0.040 Not specified
Cr (%) Not specified 0.90–1.20
V (%) Not specified 0.10–0.20
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10089 55Si7 EN 10089 50CrV4
Tensile Strength 1000–1200 MPa 1100–1300 MPa
Yield Strength ≥900 MPa ≥1000 MPa
Elongation ≥7% ≥8%
Hardness 285–363 HB 321–375 HB
Typical Applications
EN 10089 55Si7
Leaf springs, coil springs, torsion bars
EN 10089 50CrV4
Valve springs, high duty coil springs, hand tools
Key Differences
Can EN 10089 55Si7 Be Substituted With EN 10089 50CrV4?
EN 10089 55Si7 and EN 10089 50CrV4 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN 10089 55Si7
Round Bar → (3 listings)
Diameter: 30–30 mm (1.18–1.18 in)
Length: 4200–7000 mm (165.35–275.59 in)
EN 10089 50CrV4
Round Bar → (3 listings)
Diameter: 30–30 mm (1.18–1.18 in)
Length: 5000–6500 mm (196.85–255.91 in)
On M-EX Right Now
EN 10089 55Si7
3 active listings and RFQs →
EN 10089 50CrV4
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10089 55Si7 and EN 10089 50CrV4?
EN 10089 55Si7 specifies S, P which are not specified for EN 10089 50CrV4. EN 10089 50CrV4 specifies Cr, V which are not specified for EN 10089 55Si7.
Can EN 10089 55Si7 be substituted with EN 10089 50CrV4?
EN 10089 55Si7 and EN 10089 50CrV4 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.