Post Stock Login Register

GB/T 1299 Cr12MoV vs DIN 17200 30CrMoV9

Related Material — 65% match based on chemical composition and mechanical property overlap.

GB/T 1299 Cr12MoV (GB/T 1299-2014) and DIN 17200 30CrMoV9 (DIN 17200:1986) are both steel grades. GB/T 1299 Cr12MoV is classified under Tool & Die Steels, while DIN 17200 30CrMoV9 is classified under Alloy Steel — a different category, which is worth noting alongside the chemistry match below. GB/T 1299 Cr12MoV is typically used for blanking dies, forming dies, thread rolling dies, punches, shear blades, gauges, broaches, drawing dies, while DIN 17200 30CrMoV9 is commonly used for power generation components, rotors, turbine parts. GB/T 1299 Cr12MoV is defined under Guobiao Standards (GB/T), originating from China, while DIN 17200 30CrMoV9 is defined under Deutsches Institut fur Normung (DIN), originating from Germany.

As per chemical composition, GB/T 1299 Cr12MoV vs DIN 17200 30CrMoV9 is a 68.5% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 65%.

Frequently Compared With GB/T 1299 Cr12MoV:
DIN EN ISO 4957 1.2379 DIN EN ISO 4957 1.2344 GB/T 1299 4Cr5MoSiV1 AISI 52100 EN ISO 683-17 100Cr6 EN ISO 4957 1.2316 GB/T 1299 4Cr5MoSiV GOST 5950 4H5MFS GOST 5950 4H5MFS1 GB/T 1299 3Cr2W8V GOST 5950 3H2W8F IS 1570 (Part 6) 103T3
Match Breakdown
CHEMISTRY MATCH
68.5%
MECHANICAL MATCH
No shared data
OVERALL
65%
Specifications
Property GB/T 1299 Cr12MoV DIN 17200 30CrMoV9
Standard GB/T 1299-2014 DIN 17200:1986
Category Tool & Die Steels Alloy Steel
C (%) 1.45–1.70 0.26–0.34
Mn (%) ≤0.40 0.40–0.70
Si (%) ≤0.40 Not specified
Cr (%) 11.00–13.00 2.30–2.70
Mo (%) 0.40–0.60 0.90–1.10
V (%) 0.15–0.30 0.18–0.28
S (%) ≤0.030 Not specified
P (%) ≤0.030 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property GB/T 1299 Cr12MoV DIN 17200 30CrMoV9
Hardness (annealed) ≤255 HB Not specified
Hardness (hardened) 57–62 HRC Not specified
Compressive Strength 2400 MPa Not specified
Tensile Strength Not specified 900–1100 MPa
Yield Strength Not specified ≥750 MPa
Elongation Not specified ≥13%
Typical Applications
GB/T 1299 Cr12MoV
Blanking dies, forming dies, thread rolling dies, punches, shear blades, gauges, broaches, drawing dies
DIN 17200 30CrMoV9
Power generation components, rotors, turbine parts
Key Differences
Can GB/T 1299 Cr12MoV Be Substituted With DIN 17200 30CrMoV9?
GB/T 1299 Cr12MoV and DIN 17200 30CrMoV9 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
GB/T 1299 Cr12MoV
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 3100–3400 mm (122.05–133.86 in)
DIN 17200 30CrMoV9
Round Bar → (2 listings)
Diameter: 50–50 mm (1.97–1.97 in)
Length: 5500–6600 mm (216.54–259.84 in)
On M-EX Right Now
GB/T 1299 Cr12MoV
2 active listings and RFQs →
DIN 17200 30CrMoV9
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between GB/T 1299 Cr12MoV and DIN 17200 30CrMoV9?
Different category: GB/T 1299 Cr12MoV is Tool & Die Steels, DIN 17200 30CrMoV9 is Alloy Steel. GB/T 1299 Cr12MoV specifies Si, S, P which are not specified for DIN 17200 30CrMoV9.
Can GB/T 1299 Cr12MoV be substituted with DIN 17200 30CrMoV9?
GB/T 1299 Cr12MoV and DIN 17200 30CrMoV9 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.