Post Stock Login Register

GB/T 700 Q235D vs EN 10025-2 S235JR

Strong Match — 92.1% match based on chemical composition and mechanical property overlap.

GB/T 700 Q235D (GB/T 700:2006) and EN 10025-2 S235JR (EN 10025-2:2019) are both steel grades. Both fall under the Structural Steel category. GB/T 700 Q235D is typically used for hot rolled structural sheets, strips, sections and bars for welding, riveting and bolting engineering, while EN 10025-2 S235JR is commonly used for structural fabrication, bridges, buildings, general engineering. GB/T 700 Q235D is defined under Guobiao Standards (GB/T), originating from China, while EN 10025-2 S235JR is defined under European Standard (EN), originating from Europe.

As per chemical composition, GB/T 700 Q235D vs EN 10025-2 S235JR is a 90.3% match. As per mechanical properties, the match is 95.6%. Combined, this makes them a strong match overall at 92.1%.

Frequently Compared With GB/T 700 Q235D:
GOST 19281 09G2S CSA G40.21 300W CSA G40.21 480W ASTM A1008 SS Grade 50 ASTM A283C AS/NZS 3679.1 300 AS/NZS 3679.1 350 CSA G40.21 400W ASTM A572 Gr.65 CSA G40.21 260W CSA G40.21 350W CSA G40.21 400A
Match Breakdown
CHEMISTRY MATCH
90.3%
MECHANICAL MATCH
95.6%
OVERALL
92.1%
Specifications
Property GB/T 700 Q235D EN 10025-2 S235JR
Standard GB/T 700:2006 EN 10025-2:2019
Category Structural Steel Structural Steel
C (%) <=0.17 <=0.17
Si (%) <=0.35 Not specified
Mn (%) <=1.40 <=1.40
P (%) <=0.035 <=0.035
S (%) <=0.035 <=0.035
N (%) Not specified <=0.012
Cu (%) Not specified <=0.55
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property GB/T 700 Q235D EN 10025-2 S235JR
Tensile Strength 370-500 MPa 360-510 MPa
Yield Strength >=235 MPa >=235 MPa
Elongation >=26% >=26%
Condition Hot rolled, controlled rolled or normalized; yield up to 16 mm, elongation up to 40 mm (N/mm2 = MPa) Nominal thickness up to 16 mm (tensile for 3 to 100 mm, elongation for 3 to 40 mm), longitudinal test pieces
Typical Applications
GB/T 700 Q235D
Hot rolled structural sheets, strips, sections and bars for welding, riveting and bolting engineering
EN 10025-2 S235JR
Structural fabrication, bridges, buildings, general engineering
Key Differences
Can GB/T 700 Q235D Be Substituted With EN 10025-2 S235JR?
GB/T 700 Q235D and EN 10025-2 S235JR overlap closely enough on chemistry and mechanical properties that EN 10025-2 S235JR is often considered as a substitute for GB/T 700 Q235D in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
Forms & Sizes Available on M-EX
GB/T 700 Q235D
No active listings currently.
EN 10025-2 S235JR
Plate → (3 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 3300–5100 mm (129.92–200.79 in)
On M-EX Right Now
GB/T 700 Q235D
0 active listings and RFQs →
EN 10025-2 S235JR
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between GB/T 700 Q235D and EN 10025-2 S235JR?
GB/T 700 Q235D specifies Si which is not specified for EN 10025-2 S235JR. EN 10025-2 S235JR specifies N, Cu which are not specified for GB/T 700 Q235D.
Can GB/T 700 Q235D be substituted with EN 10025-2 S235JR?
GB/T 700 Q235D and EN 10025-2 S235JR overlap closely enough on chemistry and mechanical properties that EN 10025-2 S235JR is often considered as a substitute for GB/T 700 Q235D in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.