Post Stock Login Register

IS 11169 (Part 2) X12Cr12 vs ASTM A959 416Se

Strong Match — 89% match based on chemical composition and mechanical property overlap.

IS 11169 (Part 2) X12Cr12 (IS 11169 (Part 2):1989) and ASTM A959 416Se (ASTM A959:2011) are both steel grades. Both fall under the Stainless Steel category. IS 11169 (Part 2) X12Cr12 is typically used for cold heading and cold extrusion; the standard covers wires, wire rods and bars (clause 1.1), while ASTM A959 416Se is commonly used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1). IS 11169 (Part 2) X12Cr12 is defined under Bureau of Indian Standards (IS), originating from India, while ASTM A959 416Se is defined under ASTM International, originating from United States.

As per chemical composition, IS 11169 (Part 2) X12Cr12 vs ASTM A959 416Se is a 89% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 89%.

Frequently Compared With IS 11169 (Part 2) X12Cr12:
GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 IS 1570 (Part 7) 11Cr17Ni13W3TiH EN 10088-1 1.4845 GOST 5632 12Kh13 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr13H GOST 5632 08X18H10
Match Breakdown
CHEMISTRY MATCH
89%
MECHANICAL MATCH
No shared data
OVERALL
89%
Specifications
Property IS 11169 (Part 2) X12Cr12 ASTM A959 416Se
Standard IS 11169 (Part 2):1989 ASTM A959:2011
Category Stainless Steel Stainless Steel
C (%) 0.08-0.15 <=0.15
Si (%) <=1.0 <=1.00
Mn (%) <=1.0 <=1.25
Cr (%) 11.5-13.5 12.0-14.0
S (%) <=0.030 <=0.06
P (%) <=0.045 <=0.06
Se (%) Not specified >=0.15
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 11169 (Part 2) X12Cr12 ASTM A959 416Se
Yield Strength (0.2% proof) >=450 MPa Not specified
Tensile Strength 600-750 MPa Not specified
Elongation >=18% Not specified
Impact (U-notch 5 mm) >=50 J Not specified
Condition Quenched and tempered reference test piece (Table 6 treatment) Not specified
Typical Applications
IS 11169 (Part 2) X12Cr12
Cold heading and cold extrusion; the standard covers wires, wire rods and bars (clause 1.1)
ASTM A959 416Se
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
Key Differences
Can IS 11169 (Part 2) X12Cr12 Be Substituted With ASTM A959 416Se?
IS 11169 (Part 2) X12Cr12 and ASTM A959 416Se overlap closely enough on chemistry and mechanical properties that ASTM A959 416Se is often considered as a substitute for IS 11169 (Part 2) X12Cr12 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
On M-EX Right Now
IS 11169 (Part 2) X12Cr12
0 active listings and RFQs →
ASTM A959 416Se
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 11169 (Part 2) X12Cr12 and ASTM A959 416Se?
ASTM A959 416Se specifies Se which is not specified for IS 11169 (Part 2) X12Cr12.
Can IS 11169 (Part 2) X12Cr12 be substituted with ASTM A959 416Se?
IS 11169 (Part 2) X12Cr12 and ASTM A959 416Se overlap closely enough on chemistry and mechanical properties that ASTM A959 416Se is often considered as a substitute for IS 11169 (Part 2) X12Cr12 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.