Post Stock Login Register

IS 11169 (Part 2) X02Cr22Ni5Mo3N vs ASTM A959 S32506

Close Alternative — 72.1% match based on chemical composition and mechanical property overlap.

IS 11169 (Part 2) X02Cr22Ni5Mo3N (IS 11169 (Part 2):2023) and ASTM A959 S32506 (ASTM A959:2011) are both steel grades. Both fall under the Stainless Steel category. IS 11169 (Part 2) X02Cr22Ni5Mo3N is typically used for cold heading and cold extrusion of stainless steel parts; the standard covers wires, wire rods and bars of 2 to 25 mm (clause 1.1, table 12), while ASTM A959 S32506 is commonly used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1). IS 11169 (Part 2) X02Cr22Ni5Mo3N is defined under Bureau of Indian Standards (IS), originating from India, while ASTM A959 S32506 is defined under ASTM International, originating from United States.

As per chemical composition, IS 11169 (Part 2) X02Cr22Ni5Mo3N vs ASTM A959 S32506 is a 72.1% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 72.1%.

Frequently Compared With IS 11169 (Part 2) X02Cr22Ni5Mo3N:
ASTM A959 2205 ASTM A959 2304 ASTM A959 255 GOST 5632 06Kh23N28 EN 10088-1 1.4301 EN 10088-1 1.4401 EN 10088-1 1.4845 GB/T 3280 06Cr19Ni10 GOST 5632 08X18H10 EN 10088-1 1.4006 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH
Match Breakdown
CHEMISTRY MATCH
72.1%
MECHANICAL MATCH
No shared data
OVERALL
72.1%
Specifications
Property IS 11169 (Part 2) X02Cr22Ni5Mo3N ASTM A959 S32506
Standard IS 11169 (Part 2):2023 ASTM A959:2011
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.030
Cr (%) 21.0-23.0 24.0-26.0
Mn (%) <=2.00 <=1.00
Mo (%) 2.50-3.50 3.0-3.5
N (%) 0.10-0.2 0.08-0.20
Ni (%) 4.5-6.5 5.5-7.2
P (%) <=0.035 <=0.040
S (%) <=0.015 <=0.015
Si (%) <=1.00 <=0.90
W (%) Not specified 0.05-0.30
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 11169 (Part 2) X02Cr22Ni5Mo3N ASTM A959 S32506
Reduction of Area, solution annealed (+AT) >=55% (over 2 to 25 mm) Not specified
Tensile Strength, solution annealed (+AT) <=880 MPa (over 2 to 25 mm) Not specified
Typical Applications
IS 11169 (Part 2) X02Cr22Ni5Mo3N
Cold heading and cold extrusion of stainless steel parts; the standard covers wires, wire rods and bars of 2 to 25 mm (clause 1.1, Table 12)
ASTM A959 S32506
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
Key Differences
Can IS 11169 (Part 2) X02Cr22Ni5Mo3N Be Substituted With ASTM A959 S32506?
IS 11169 (Part 2) X02Cr22Ni5Mo3N and ASTM A959 S32506 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
IS 11169 (Part 2) X02Cr22Ni5Mo3N
0 active listings and RFQs →
ASTM A959 S32506
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 11169 (Part 2) X02Cr22Ni5Mo3N and ASTM A959 S32506?
ASTM A959 S32506 specifies W which is not specified for IS 11169 (Part 2) X02Cr22Ni5Mo3N.
Can IS 11169 (Part 2) X02Cr22Ni5Mo3N be substituted with ASTM A959 S32506?
IS 11169 (Part 2) X02Cr22Ni5Mo3N and ASTM A959 S32506 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.