Post Stock Login Register

IS 1570 (Part 7) 11Cr17Ni13W3TiH vs EN 10088-1 1.4401

Minimal Match — 33.1% match based on chemical composition and mechanical property overlap.

IS 1570 (Part 7) 11Cr17Ni13W3TiH (IS 1570 (Part 7):1992) and EN 10088-1 1.4401 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. IS 1570 (Part 7) 11Cr17Ni13W3TiH is typically used for boilers, pressure vessels, steam turbines, steam and water piping and other power plant equipment working at elevated temperature, while EN 10088-1 1.4401 is commonly used for marine, chemical processing, pharmaceutical equipment. IS 1570 (Part 7) 11Cr17Ni13W3TiH is defined under Bureau of Indian Standards (IS), originating from India, while EN 10088-1 1.4401 is defined under European Standard (EN), originating from Europe.

As per chemical composition, IS 1570 (Part 7) 11Cr17Ni13W3TiH vs EN 10088-1 1.4401 is a 49.6% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 33.1%.

Frequently Compared With IS 1570 (Part 7) 11Cr17Ni13W3TiH:
GB/T 3280 06Cr19Ni10 ASTM A959 .- IS 1570 (Part 7) 12Cr12MoVH EN 10088-1 1.4301 GOST 5632 12Kh13 IS 1570 (Part 7) 20Cr12MoNiVH GOST 5632 08X18H10 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr13H GOST 5632 06Kh23N28 EN 10088-1 1.4006 IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
49.6%
MECHANICAL MATCH
0%
OVERALL
33.1%
Specifications
Property IS 1570 (Part 7) 11Cr17Ni13W3TiH EN 10088-1 1.4401
Standard IS 1570 (Part 7):1992 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) 0.07-0.15 ≤0.07
Si (%) <=1.00 ≤1.00
Mn (%) <=1.00 ≤2.00
P (%) <=0.045 Not specified
S (%) <=0.030 Not specified
Cr (%) 15.5-17.50 16.5–18.5
Ni (%) 12.00-14.50 10.5–13.5
W (%) 2.5-3.5 Not specified
Ti (%) >=4xC, <=0.80 Not specified
B (%) <=0.0006 Not specified
Mo (%) Not specified 2.0–2.5
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 1570 (Part 7) 11Cr17Ni13W3TiH EN 10088-1 1.4401
Tensile Strength 600-800 MPa ≥520 MPa
Yield Strength >=390 MPa (0.2 % proof stress) ≥210 MPa
Elongation >=25% ≥40%
Condition Bars, forgings, pipes, hot cold worked, thickness up to 60 (first row of Table 3) Not specified
Hardness Not specified ≤215 HB
Typical Applications
IS 1570 (Part 7) 11Cr17Ni13W3TiH
Boilers, pressure vessels, steam turbines, steam and water piping and other power plant equipment working at elevated temperature
EN 10088-1 1.4401
Marine, chemical processing, pharmaceutical equipment
Key Differences
Can IS 1570 (Part 7) 11Cr17Ni13W3TiH Be Substituted With EN 10088-1 1.4401?
IS 1570 (Part 7) 11Cr17Ni13W3TiH and EN 10088-1 1.4401 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
IS 1570 (Part 7) 11Cr17Ni13W3TiH
No active listings currently.
EN 10088-1 1.4401
Sheet → (4 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2500–3400 mm (98.43–133.86 in)
On M-EX Right Now
IS 1570 (Part 7) 11Cr17Ni13W3TiH
0 active listings and RFQs →
EN 10088-1 1.4401
4 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 1570 (Part 7) 11Cr17Ni13W3TiH and EN 10088-1 1.4401?
IS 1570 (Part 7) 11Cr17Ni13W3TiH specifies P, S, W, Ti which are not specified for EN 10088-1 1.4401. EN 10088-1 1.4401 specifies Mo which is not specified for IS 1570 (Part 7) 11Cr17Ni13W3TiH.
Can IS 1570 (Part 7) 11Cr17Ni13W3TiH be substituted with EN 10088-1 1.4401?
IS 1570 (Part 7) 11Cr17Ni13W3TiH and EN 10088-1 1.4401 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.