Post Stock Login Register

IS 1570 (Part 7) 12Cr12MoVH vs EN 10088-1 1.4006

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

IS 1570 (Part 7) 12Cr12MoVH (IS 1570 (Part 7):1992) and EN 10088-1 1.4006 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. IS 1570 (Part 7) 12Cr12MoVH is typically used for boilers, pressure vessels, steam turbines, steam and water piping and other power plant equipment working at elevated temperature, while EN 10088-1 1.4006 is commonly used for cutlery, turbine blades, fasteners, surgical instruments. IS 1570 (Part 7) 12Cr12MoVH is defined under Bureau of Indian Standards (IS), originating from India, while EN 10088-1 1.4006 is defined under European Standard (EN), originating from Europe.

As per chemical composition, IS 1570 (Part 7) 12Cr12MoVH vs EN 10088-1 1.4006 is a 63% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With IS 1570 (Part 7) 12Cr12MoVH:
IS 1570 (Part 7) 12Cr13H EN 10088-1 1.4401 IS 1570 (Part 7) 11Cr17Ni13W3TiH EN 10088-1 1.4301 GOST 5632 06Kh23N28 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 20Cr12MoNiVH GB/T 3280 06Cr19Ni10 IS 1570 (Part 7) 12Cr12Ni2Mo GOST 5632 12Kh13 ASTM A959 202 ASTM A959 201L
Match Breakdown
CHEMISTRY MATCH
63%
MECHANICAL MATCH
0%
OVERALL
35%
Specifications
Property IS 1570 (Part 7) 12Cr12MoVH EN 10088-1 1.4006
Standard IS 1570 (Part 7):1992 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) 0.08-0.16 0.08–0.15
Si (%) <=0.60 ≤1.00
Mn (%) 0.40-1.00 ≤1.50
P (%) <=0.040 Not specified
S (%) <=0.035 Not specified
Cr (%) 11.5-13.00 11.5–13.5
Ni (%) <=1.0 ≤0.75
Mo (%) 0.40-0.80 Not specified
V (%) 0.10-0.30 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 1570 (Part 7) 12Cr12MoVH EN 10088-1 1.4006
Tensile Strength 770-930 MPa ≥540 MPa (annealed)
Yield Strength >=585 MPa (0.2 % proof stress) Not specified
Elongation >=15% ≥18%
Condition Bars, forgings, Q+T, thickness up to 150 (first row of Table 3) Not specified
Hardness HRC Not specified 36–45 (hardened)
Typical Applications
IS 1570 (Part 7) 12Cr12MoVH
Boilers, pressure vessels, steam turbines, steam and water piping and other power plant equipment working at elevated temperature
EN 10088-1 1.4006
Cutlery, turbine blades, fasteners, surgical instruments
Key Differences
Can IS 1570 (Part 7) 12Cr12MoVH Be Substituted With EN 10088-1 1.4006?
IS 1570 (Part 7) 12Cr12MoVH and EN 10088-1 1.4006 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
IS 1570 (Part 7) 12Cr12MoVH
No active listings currently.
EN 10088-1 1.4006
Sheet → (3 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2700–3400 mm (106.3–133.86 in)
On M-EX Right Now
IS 1570 (Part 7) 12Cr12MoVH
0 active listings and RFQs →
EN 10088-1 1.4006
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 1570 (Part 7) 12Cr12MoVH and EN 10088-1 1.4006?
IS 1570 (Part 7) 12Cr12MoVH specifies P, S, Mo, V which are not specified for EN 10088-1 1.4006.
Can IS 1570 (Part 7) 12Cr12MoVH be substituted with EN 10088-1 1.4006?
IS 1570 (Part 7) 12Cr12MoVH and EN 10088-1 1.4006 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.