Post Stock Login Register

IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH vs EN 10088-1 1.4301

Minimal Match — 25.6% match based on chemical composition and mechanical property overlap.

IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH (IS 1570 (Part 7):1992) and EN 10088-1 1.4301 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH is typically used for boilers, pressure vessels, steam turbines, steam and water piping and other power plant equipment working at elevated temperature, while EN 10088-1 1.4301 is commonly used for food equipment, chemical vessels, architectural, kitchenware. IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH is defined under Bureau of Indian Standards (IS), originating from India, while EN 10088-1 1.4301 is defined under European Standard (EN), originating from Europe.

As per chemical composition, IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH vs EN 10088-1 1.4301 is a 38.4% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 25.6%.

Frequently Compared With IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH:
IS 1570 (Part 7) 12Cr12MoH GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr13H ASTM A959 .- GB/T 3280 06Cr19Ni10 EN 10088-1 1.4006 EN 10088-1 1.4401 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
38.4%
MECHANICAL MATCH
0%
OVERALL
25.6%
Specifications
Property IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH EN 10088-1 1.4301
Standard IS 1570 (Part 7):1992 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) 0.03-0.08 ≤0.07
Si (%) <=1.00 ≤1.00
Mn (%) <=2.00 ≤2.00
P (%) <=0.045 ≤0.045
S (%) <=0.030 ≤0.030
Cr (%) 13.5-16.00 17.5–19.5
Ni (%) 24.00-27.00 8.0–10.5
Mo (%) 1.00-1.50 Not specified
V (%) 0.10-0.50 Not specified
Ti (%) 1.9-2.30 Not specified
Al (%) <=0.35 Not specified
B (%) 0.003-0.010 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH EN 10088-1 1.4301
Tensile Strength 900-1100 MPa ≥520 MPa
Yield Strength >=600 MPa (0.2 % proof stress) ≥210 MPa
Elongation >=15% ≥45%
Condition Bars, forgings, pipes, plates, S+P, thickness over 5 to 250 (first row of Table 3) Not specified
Hardness Not specified ≤215 HB
Typical Applications
IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH
Boilers, pressure vessels, steam turbines, steam and water piping and other power plant equipment working at elevated temperature
EN 10088-1 1.4301
Food equipment, chemical vessels, architectural, kitchenware
Key Differences
Can IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH Be Substituted With EN 10088-1 1.4301?
IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH and EN 10088-1 1.4301 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH
No active listings currently.
EN 10088-1 1.4301
Sheet → (3 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2500–3300 mm (98.43–129.92 in)
On M-EX Right Now
IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH
0 active listings and RFQs →
EN 10088-1 1.4301
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH and EN 10088-1 1.4301?
IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH specifies Mo, V, Ti, Al which are not specified for EN 10088-1 1.4301.
Can IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH be substituted with EN 10088-1 1.4301?
IS 1570 (Part 7) 6Ni25Cr15Ti2MoVBH and EN 10088-1 1.4301 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.