Post Stock Login Register

IS 6603 X02Cr25Ni7Mo4CuWN vs EN 10088-1 X2CrNiMoCuN25-6-3

Strong Match — 87.2% match based on chemical composition and mechanical property overlap.

IS 6603 X02Cr25Ni7Mo4CuWN (IS 6603:2024) and EN 10088-1 X2CrNiMoCuN25-6-3 (EN 10088-1:2023) are both steel grades. Both fall under the Stainless Steel category. IS 6603 X02Cr25Ni7Mo4CuWN is defined under Bureau of Indian Standards (IS), originating from India, while EN 10088-1 X2CrNiMoCuN25-6-3 is defined under European Standard (EN), originating from Europe.

As per chemical composition, IS 6603 X02Cr25Ni7Mo4CuWN vs EN 10088-1 X2CrNiMoCuN25-6-3 is a 87.2% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 87.2%.

Frequently Compared With IS 6603 X02Cr25Ni7Mo4CuWN:
GOST 5632 06Kh23N28 EN 10088-1 1.4401 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH GB/T 3280 06Cr19Ni10 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12Ni2Mo ASTM A959 .-
Match Breakdown
CHEMISTRY MATCH
87.2%
MECHANICAL MATCH
No shared data
OVERALL
87.2%
Specifications
Property IS 6603 X02Cr25Ni7Mo4CuWN EN 10088-1 X2CrNiMoCuN25-6-3
Standard IS 6603:2024 EN 10088-1:2023
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.030
Si (%) <=1.00 <=0.70
Mn (%) <=1.00 <=2.00
P (%) <=0.035 <=0.035
S (%) <=0.015 <=0.015
Cr (%) 24.0-26.0 24.0-26.0
Mo (%) 3.0-4.0 3.00-4.0
Ni (%) 6.0-8.0 6.0-8.0
N (%) 0.20-0.30 0.20-0.30
Cu (%) 0.50-1.00 1.00-2.50
W (%) 0.50-1.00 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 6603 X02Cr25Ni7Mo4CuWN EN 10088-1 X2CrNiMoCuN25-6-3
Tensile Strength >=730 MPa Not specified
Yield Strength >=530 MPa Not specified
Elongation >=25% Not specified
Hardness <=290 HB Not specified
Condition Solution annealed, conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 160 mm; Tensile Strength is a minimum as printed, hardness for guidance only Not specified
Typical Applications
IS 6603 X02Cr25Ni7Mo4CuWN
General purposes, semi-finished products, bars, wire rods and bright bars
EN 10088-1 X2CrNiMoCuN25-6-3
Not documented
Key Differences
Can IS 6603 X02Cr25Ni7Mo4CuWN Be Substituted With EN 10088-1 X2CrNiMoCuN25-6-3?
IS 6603 X02Cr25Ni7Mo4CuWN and EN 10088-1 X2CrNiMoCuN25-6-3 overlap closely enough on chemistry and mechanical properties that EN 10088-1 X2CrNiMoCuN25-6-3 is often considered as a substitute for IS 6603 X02Cr25Ni7Mo4CuWN in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
On M-EX Right Now
IS 6603 X02Cr25Ni7Mo4CuWN
0 active listings and RFQs →
EN 10088-1 X2CrNiMoCuN25-6-3
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 6603 X02Cr25Ni7Mo4CuWN and EN 10088-1 X2CrNiMoCuN25-6-3?
IS 6603 X02Cr25Ni7Mo4CuWN specifies W which is not specified for EN 10088-1 X2CrNiMoCuN25-6-3.
Can IS 6603 X02Cr25Ni7Mo4CuWN be substituted with EN 10088-1 X2CrNiMoCuN25-6-3?
IS 6603 X02Cr25Ni7Mo4CuWN and EN 10088-1 X2CrNiMoCuN25-6-3 overlap closely enough on chemistry and mechanical properties that EN 10088-1 X2CrNiMoCuN25-6-3 is often considered as a substitute for IS 6603 X02Cr25Ni7Mo4CuWN in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.