Post Stock Login Register

JIS G4105 SCM435 vs SAE J404 4135

Strong Match — 89.2% match based on chemical composition and mechanical property overlap.

JIS G4105 SCM435 (JIS G4105:1979) and SAE J404 4135 (SAE J404:2009) are both steel grades. Both fall under the Alloy Steel category. JIS G4105 SCM435 is typically used for gears, shafts, high tensile bolts, while SAE J404 4135 is commonly used for gears, shafts, pressure vessels, high tensile bolts. JIS G4105 SCM435 is defined under Japanese Industrial Standards (JIS), originating from Japan, while SAE J404 4135 is defined under SAE International, originating from United States.

As per chemical composition, JIS G4105 SCM435 vs SAE J404 4135 is a 89.2% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 89.2%.

Frequently Compared With JIS G4105 SCM435:
NF A35-565 100C6 UNI 11234 100Cr6 GB/T 3077 12Cr2Ni4A GOST 4543 12HN3A IS 4367 07Cr4Mo6 IS 4367 10Cr9Mo10 IS 1570 (Part 4) 105Cr5 IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 103Cr6 IS 1570 (Part 4) 10Cr20Mo6 IS 1570 (Part 7) 10Cr36Mo10H IS 1570 (Part 4) 07Cr4Mo6
Match Breakdown
CHEMISTRY MATCH
89.2%
MECHANICAL MATCH
No shared data
OVERALL
89.2%
Specifications
Property JIS G4105 SCM435 SAE J404 4135
Standard JIS G4105:1979 SAE J404:2009
Category Alloy Steel Alloy Steel
C (%) 0.33–0.38 0.33-0.38
Si (%) 0.15–0.35 0.15-0.35
Mn (%) 0.60–0.90 0.70-0.90
Cr (%) 0.90–1.20 0.80-1.10
Mo (%) 0.15–0.30 0.15-0.25
P (%) Not specified <=0.030
S (%) Not specified <=0.040
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property JIS G4105 SCM435 SAE J404 4135
Tensile Strength ≥830 MPa Not specified
Yield Strength ≥685 MPa Not specified
Elongation ≥15% Not specified
Hardness 248–302 HB Not specified
Typical Applications
JIS G4105 SCM435
Gears, shafts, high tensile bolts
SAE J404 4135
Gears, shafts, pressure vessels, high tensile bolts
Key Differences
Can JIS G4105 SCM435 Be Substituted With SAE J404 4135?
JIS G4105 SCM435 and SAE J404 4135 overlap closely enough on chemistry and mechanical properties that SAE J404 4135 is often considered as a substitute for JIS G4105 SCM435 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
Forms & Sizes Available on M-EX
JIS G4105 SCM435
Round Bar → (2 listings)
Diameter: 50–50 mm (1.97–1.97 in)
Length: 4600–5300 mm (181.1–208.66 in)
SAE J404 4135
Round Bar → (2 listings)
Diameter: 50–50 mm (1.97–1.97 in)
Length: 6100–6700 mm (240.16–263.78 in)
On M-EX Right Now
JIS G4105 SCM435
2 active listings and RFQs →
SAE J404 4135
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between JIS G4105 SCM435 and SAE J404 4135?
SAE J404 4135 specifies P, S which are not specified for JIS G4105 SCM435.
Can JIS G4105 SCM435 be substituted with SAE J404 4135?
JIS G4105 SCM435 and SAE J404 4135 overlap closely enough on chemistry and mechanical properties that SAE J404 4135 is often considered as a substitute for JIS G4105 SCM435 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.