Post Stock Login Register

JIS G4105 SCM440 vs NF A35-565 100C6

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

JIS G4105 SCM440 (JIS G4105:1979) and NF A35-565 100C6 are both steel grades. Both fall under the Alloy Steel category. JIS G4105 SCM440 is typically used for automotive parts, gears, shafts, bolts, dies, while NF A35-565 100C6 is commonly used for ball bearings, roller bearings, bearing races, rollers, precision tools, wear resistant parts. JIS G4105 SCM440 is defined under Japanese Industrial Standards (JIS), originating from Japan, while NF A35-565 100C6 is defined under Association Francaise de Normalisation (NF), originating from France.

As per chemical composition, JIS G4105 SCM440 vs NF A35-565 100C6 is a 65.8% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With JIS G4105 SCM440:
GB/T 3077 12Cr2Ni4A GOST 4543 12HN3A UNI 11234 100Cr6 IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 105Cr5 IS 1570 (Part 4) 10Cr20Mo6 IS 1570 (Part 7) 10Cr36Mo10H IS 1570 (Part 4) 10Mo6 IS 1570 (Part 4) 07Cr4Mo6 IS 4367 10Cr9Mo10 IS 4367 07Cr4Mo6 IS 1570 (Part 4) 103Cr6
Match Breakdown
CHEMISTRY MATCH
65.8%
MECHANICAL MATCH
0%
OVERALL
35%
Specifications
Property JIS G4105 SCM440 NF A35-565 100C6
Standard JIS G4105:1979 NF A35-565
Category Alloy Steel Alloy Steel
C (%) 0.38–0.43 0.95-1.05
Si (%) 0.15–0.35 0.15-0.35
Mn (%) 0.60–0.90 0.25-0.45
Cr (%) 0.90–1.20 1.35-1.65
Mo (%) 0.15–0.30 Not specified
S (%) ≤0.030 <=0.025
P (%) ≤0.030 <=0.027
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property JIS G4105 SCM440 NF A35-565 100C6
Tensile Strength ≥930 MPa 850-1100 MPa
Yield Strength ≥785 MPa Not specified
Elongation ≥12% Not specified
Hardness 269–331 HB 60-66 HRC
Typical Applications
JIS G4105 SCM440
Automotive parts, gears, shafts, bolts, dies
NF A35-565 100C6
ball bearings, roller bearings, bearing races, rollers, precision tools, wear resistant parts
Key Differences
Can JIS G4105 SCM440 Be Substituted With NF A35-565 100C6?
JIS G4105 SCM440 and NF A35-565 100C6 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
JIS G4105 SCM440
Round Bar → (3 listings)
Diameter: 50–50 mm (1.97–1.97 in)
Length: 5400–7000 mm (212.6–275.59 in)
NF A35-565 100C6
Round Bar → (2 listings)
Diameter: 50–50 mm (1.97–1.97 in)
Length: 6700–6700 mm (263.78–263.78 in)
On M-EX Right Now
JIS G4105 SCM440
3 active listings and RFQs →
NF A35-565 100C6
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between JIS G4105 SCM440 and NF A35-565 100C6?
JIS G4105 SCM440 specifies Mo which is not specified for NF A35-565 100C6.
Can JIS G4105 SCM440 be substituted with NF A35-565 100C6?
JIS G4105 SCM440 and NF A35-565 100C6 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.