Post Stock Login Register

NF A35-552 XC38 vs BS 970 (Part 1) 080A20

Related Material — 69.9% match based on chemical composition and mechanical property overlap.

NF A35-552 XC38 (NF A35-552:1986) and BS 970 (Part 1) 080A20 (BS 970 (Part 1):1991) are both steel grades. Both fall under the Carbon Steel category. NF A35-552 XC38 is typically used for shafts, pins, connecting rods, machined parts, forgings, agricultural equipment parts, while BS 970 (Part 1) 080A20 is commonly used for used for nuts, bolts, hydraulic fittings, precision turned parts, sleeves, and couplings.. NF A35-552 XC38 is defined under Association Francaise de Normalisation (NF), originating from France, while BS 970 (Part 1) 080A20 is defined under British Standards (BS), originating from United Kingdom.

As per chemical composition, NF A35-552 XC38 vs BS 970 (Part 1) 080A20 is a 79.7% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 69.9%.

Frequently Compared With NF A35-552 XC38:
BS 970 (Part 1) 040A10 BS 970 (Part 3) 070M55 BS 970 (Part 1) 040A04 BS 970 (Part 1) 040A12 BS 970 (Part 1) 045A10 BS 970 (Part 3) 070M20 BS 970 (Part 1) 045M10 BS 970 (Part 1) 060A40 BS 970 (Part 1) 045A10 BS 970 (Part 3) 045A10 BS 970 (Part 1) 045M10 BS 970 (Part 3) 045M10
Match Breakdown
CHEMISTRY MATCH
79.7%
MECHANICAL MATCH
No shared data
OVERALL
69.9%
Specifications
Property NF A35-552 XC38 BS 970 (Part 1) 080A20
Standard NF A35-552:1986 BS 970 (Part 1):1991
Category Carbon Steel Carbon Steel
C (%) 0.35-0.42 0.18-0.23
Si (%) 0.10-0.40 Not specified
Mn (%) 0.50-0.80 0.70-0.90
S (%) <=0.035 Not specified
P (%) <=0.035 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property NF A35-552 XC38 BS 970 (Part 1) 080A20
Tensile Strength 540-680 MPa Not specified
Yield Strength >=320 MPa Not specified
Elongation >=17% Not specified
Hardness 160-200 HB Not specified
Typical Applications
NF A35-552 XC38
shafts, pins, connecting rods, machined parts, forgings, agricultural equipment parts
BS 970 (Part 1) 080A20
Used for nuts, bolts, hydraulic fittings, precision turned parts, sleeves, and couplings.
Key Differences
Can NF A35-552 XC38 Be Substituted With BS 970 (Part 1) 080A20?
NF A35-552 XC38 and BS 970 (Part 1) 080A20 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
NF A35-552 XC38
Round Bar → (2 listings)
Diameter: 40–40 mm (1.57–1.57 in)
Length: 6300–7000 mm (248.03–275.59 in)
BS 970 (Part 1) 080A20
Round Bar → (2 listings)
Diameter: 40–40 mm (1.57–1.57 in)
Length: 4800–6600 mm (188.98–259.84 in)
On M-EX Right Now
NF A35-552 XC38
2 active listings and RFQs →
BS 970 (Part 1) 080A20
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between NF A35-552 XC38 and BS 970 (Part 1) 080A20?
NF A35-552 XC38 specifies Si, S, P which are not specified for BS 970 (Part 1) 080A20.
Can NF A35-552 XC38 be substituted with BS 970 (Part 1) 080A20?
NF A35-552 XC38 and BS 970 (Part 1) 080A20 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.