Post Stock Login Register

SAE J403 1002 vs EN 10025-2 E295

Related Material — 65% match based on chemical composition and mechanical property overlap.

SAE J403 1002 (SAE J403:2014) and EN 10025-2 E295 (EN 10025-2:2019) are both steel grades. SAE J403 1002 is classified under Carbon Steel, while EN 10025-2 E295 is classified under Structural Steel — a different category, which is worth noting alongside the chemistry match below. SAE J403 1002 is typically used for chemistry-only grade; product scope as listed in the composition notes, while EN 10025-2 E295 is commonly used for hot rolled products of structural steels. SAE J403 1002 is defined under SAE International, originating from United States, while EN 10025-2 E295 is defined under European Standard (EN), originating from Europe.

As per chemical composition, SAE J403 1002 vs EN 10025-2 E295 is a 87.2% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 65%.

Frequently Compared With SAE J403 1002:
BS 970 (Part 3) 070M55 BS 970 (Part 1) 040A10 BS 970 (Part 1) 045M10 BS 970 (Part 1) 060A32 BS 970 (Part 1) 045A10 BS 970 (Part 1) 045A10 BS 970 (Part 3) 045A10 BS 970 (Part 3) 045M10 BS 970 (Part 1) 055M15 BS 970 (Part 1) 040A04 BS 970 (Part 1) 040A12 BS 970 (Part 1) 045M10
Match Breakdown
CHEMISTRY MATCH
87.2%
MECHANICAL MATCH
No shared data
OVERALL
65%
Specifications
Property SAE J403 1002 EN 10025-2 E295
Standard SAE J403:2014 EN 10025-2:2019
Category Carbon Steel Structural Steel
C (%) 0.02-0.04 Not specified
Mn (%) <=0.35 Not specified
P (%) <=0.030 (flat rolled), <=0.040 (long products) <=0.045
S (%) <=0.035 (flat rolled), <=0.050 (long products) <=0.045
N (%) Not specified <=0.012
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property SAE J403 1002 EN 10025-2 E295
Tensile Strength Not specified 470-610 MPa
Yield Strength Not specified >=295 MPa
Elongation Not specified >=20%
Condition Not specified Nominal thickness up to 16 mm (tensile for 3 to 100 mm, elongation for 3 to 40 mm), longitudinal test pieces
Typical Applications
SAE J403 1002
Chemistry-only grade; product scope as listed in the composition notes
EN 10025-2 E295
Hot rolled products of structural steels
Key Differences
Can SAE J403 1002 Be Substituted With EN 10025-2 E295?
SAE J403 1002 and EN 10025-2 E295 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
SAE J403 1002
0 active listings and RFQs →
EN 10025-2 E295
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between SAE J403 1002 and EN 10025-2 E295?
Different category: SAE J403 1002 is Carbon Steel, EN 10025-2 E295 is Structural Steel. SAE J403 1002 specifies C, Mn which are not specified for EN 10025-2 E295. EN 10025-2 E295 specifies N which is not specified for SAE J403 1002.
Can SAE J403 1002 be substituted with EN 10025-2 E295?
SAE J403 1002 and EN 10025-2 E295 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.