Post Stock Login Register

AS/NZS 1595 C350 vs IS 2062 (Part 1) E275C

Close Alternative — 77% match based on chemical composition and mechanical property overlap.

AS/NZS 1595 C350 (AS/NZS 1595:1998) and IS 2062 (Part 1) E275C (IS 2062 (Part 1):2025) are both steel grades. Both fall under the Structural Steel category. AS/NZS 1595 C350 is typically used for cold-rolled structural steel sheet; roll-forming, cold-formed structural sections, purlins, while IS 2062 (Part 1) E275C is commonly used for structural work: welded, bolted and riveted structures and general engineering purposes. AS/NZS 1595 C350 is defined under Australian/New Zealand Standard (AS/NZS), originating from Australia/New Zealand, while IS 2062 (Part 1) E275C is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, AS/NZS 1595 C350 vs IS 2062 (Part 1) E275C is a 98.9% match. As per mechanical properties, the match is 33.3%. Combined, this makes them a close alternative overall at 77%.

Frequently Compared With AS/NZS 1595 C350:
CSA G40.21 480W CSA G40.21 300W CSA G40.21 350W ASTM A1008 SS Grade 50 CSA G40.21 400A AS/NZS 3679.1 300 CSA G40.21 400W CSA G40.21 260W GOST 19281 09G2S AS/NZS 3679.1 350 ASTM A1008 SS Grade 80 ASTM A283C
Match Breakdown
CHEMISTRY MATCH
98.9%
MECHANICAL MATCH
33.3%
OVERALL
77%
Specifications
Property AS/NZS 1595 C350 IS 2062 (Part 1) E275C
Standard AS/NZS 1595:1998 IS 2062 (Part 1):2025
Category Structural Steel Structural Steel
C (%) <=0.20 <=0.20
Mn (%) <=1.50 <=1.50
Si (%) <=0.50 <=0.40
P (%) <=0.040 <=0.040
S (%) <=0.040 <=0.040
CEV (%) Not specified <=0.41
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property AS/NZS 1595 C350 IS 2062 (Part 1) E275C
Tensile Strength 430 MPa min >=430 MPa
Yield Strength 350 MPa min 275 MPa (<=16mm) / 265 MPa (16-40mm) / 255 MPa (40-100mm) / 225 MPa (>100mm)
Elongation 14% min >=23% (<=40mm) / >=22% (40-63mm) / >=21% (63-100mm) / >=19% (>100mm)
Impact Energy Not specified >=27 J at -20°C
Typical Applications
AS/NZS 1595 C350
Cold-rolled structural steel sheet; roll-forming, cold-formed structural sections, purlins
IS 2062 (Part 1) E275C
Structural work: welded, bolted and riveted structures and general engineering purposes
Key Differences
Can AS/NZS 1595 C350 Be Substituted With IS 2062 (Part 1) E275C?
AS/NZS 1595 C350 and IS 2062 (Part 1) E275C are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
AS/NZS 1595 C350
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2500–4600 mm (98.43–181.1 in)
IS 2062 (Part 1) E275C
No active listings currently.
On M-EX Right Now
AS/NZS 1595 C350
2 active listings and RFQs →
IS 2062 (Part 1) E275C
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between AS/NZS 1595 C350 and IS 2062 (Part 1) E275C?
IS 2062 (Part 1) E275C specifies CEV which is not specified for AS/NZS 1595 C350.
Can AS/NZS 1595 C350 be substituted with IS 2062 (Part 1) E275C?
AS/NZS 1595 C350 and IS 2062 (Part 1) E275C are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.