Post Stock Login Register

AS/NZS 3679.1 350 vs IS 2062 E250A

Related Material — 64.8% match based on chemical composition and mechanical property overlap.

AS/NZS 3679.1 350 (AS/NZS 3679.1:2016) and IS 2062 E250A (IS 2062:2011) are both steel grades. Both fall under the Structural Steel category. AS/NZS 3679.1 350 is typically used for hot-rolled structural bars and sections for primary structural beams, columns, and framing, while IS 2062 E250A is commonly used for structural fabrication, bridges, industrial sheds, machinery frames, general engineering components, plates, welded structures. AS/NZS 3679.1 350 is defined under Australian/New Zealand Standard (AS/NZS), originating from Australia/New Zealand, while IS 2062 E250A is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, AS/NZS 3679.1 350 vs IS 2062 E250A is a 97.2% match. As per mechanical properties, the match is 0%. Combined, this makes them a related material overall at 64.8%.

Frequently Compared With AS/NZS 3679.1 350:
CSA G40.21 480W CSA G40.21 350W CSA G40.21 400W AS/NZS 1595 C450 ASTM A1008 SS Grade 50 IS 2062 E250B0 ASTM A1008 SS Grade 80 AS/NZS 1595 C350 ASTM A572 Grade 50 ASTM A283C ASTM A572 Gr.65 CSA G40.21 260W
Match Breakdown
CHEMISTRY MATCH
97.2%
MECHANICAL MATCH
0%
OVERALL
64.8%
Specifications
Property AS/NZS 3679.1 350 IS 2062 E250A
Standard AS/NZS 3679.1:2016 IS 2062:2011
Category Structural Steel Structural Steel
C (%) <=0.22 <=0.23
Mn (%) <=1.70 <=1.50
Si (%) <=0.50 <=0.40
P (%) <=0.040 <=0.045
S (%) <=0.040 <=0.045
CEV (%) Not specified <=0.42
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property AS/NZS 3679.1 350 IS 2062 E250A
Tensile Strength 480-640 MPa >=410 MPa
Yield Strength 350 MPa min 250 MPa (<=20mm) / 240 MPa (20-40mm) / 230 MPa (>40mm)
Elongation 20% min >=23%
Impact Not specified not required
Typical Applications
AS/NZS 3679.1 350
Hot-rolled structural bars and sections for primary structural beams, columns, and framing
IS 2062 E250A
structural fabrication, bridges, industrial sheds, machinery frames, general engineering components, plates, welded structures
Key Differences
Can AS/NZS 3679.1 350 Be Substituted With IS 2062 E250A?
AS/NZS 3679.1 350 and IS 2062 E250A share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
AS/NZS 3679.1 350
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2900–3200 mm (114.17–125.98 in)
IS 2062 E250A
Angle → (6 listings)
Leg 1: 75–90 mm (2.95–3.54 in)
Leg 2: 60–75 mm (2.36–2.95 in)
Thickness: 6–6 mm (0.24–0.24 in)
Plate → (6 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2800–3600 mm (110.24–141.73 in)
Flat Bar → (3 listings)
Thickness: 12–12 mm (0.47–0.47 in)
Width: 100–100 mm (3.94–3.94 in)
Length: 5400–7000 mm (212.6–275.59 in)
On M-EX Right Now
AS/NZS 3679.1 350
2 active listings and RFQs →
IS 2062 E250A
15 active listings and RFQs →
Frequently Asked Questions
What is the difference between AS/NZS 3679.1 350 and IS 2062 E250A?
IS 2062 E250A specifies CEV which is not specified for AS/NZS 3679.1 350.
Can AS/NZS 3679.1 350 be substituted with IS 2062 E250A?
AS/NZS 3679.1 350 and IS 2062 E250A share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.