Post Stock Login Register

ASTM A240/A240M S30435 vs ASTM A959 347

Close Alternative — 83.3% match based on chemical composition and mechanical property overlap.

ASTM A240/A240M S30435 (ASTM A240/A240M:2025) and ASTM A959 347 (ASTM A959:2011) are both steel grades. Both fall under the Stainless Steel category. ASTM A240/A240M S30435 is typically used for pressure vessels and general applications (plate, sheet and strip), while ASTM A959 347 is commonly used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1). ASTM A240/A240M S30435 is defined under ASTM International, originating from United States, while ASTM A959 347 is defined under ASTM International, originating from United States.

As per chemical composition, ASTM A240/A240M S30435 vs ASTM A959 347 is a 83.3% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 83.3%.

Frequently Compared With ASTM A240/A240M S30435:
EN 10088-1 1.4845 GOST 5632 06Kh23N28 ASTM A959 .- EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4401 IS 1570 (Part 7) 11Cr17Ni13W3TiH GB/T 3280 06Cr19Ni10 GOST 5632 08X18H10 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
83.3%
MECHANICAL MATCH
No shared data
OVERALL
83.3%
Specifications
Property ASTM A240/A240M S30435 ASTM A959 347
Standard ASTM A240/A240M:2025 ASTM A959:2011
Category Stainless Steel Stainless Steel
C (%) <=0.08 <=0.08
Mn (%) <=2.00 <=2.00
P (%) <=0.045 <=0.045
S (%) <=0.030 <=0.030
Si (%) <=1.00 <=1.00
Cr (%) 16.0-18.0 17.0-19.0
Ni (%) 7.0-9.0 9.0-12.0
Cu (%) 1.50-3.00 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A240/A240M S30435 ASTM A959 347
Tensile Strength >=450 MPa Not specified
Yield Strength >=155 MPa Not specified
Elongation >=45% Not specified
Hardness <=187 HB Not specified
Condition Plate, sheet and strip; yield by 0.2 percent offset Not specified
Typical Applications
ASTM A240/A240M S30435
Pressure vessels and general applications (plate, sheet and strip)
ASTM A959 347
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
Key Differences
Can ASTM A240/A240M S30435 Be Substituted With ASTM A959 347?
ASTM A240/A240M S30435 and ASTM A959 347 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
ASTM A240/A240M S30435
0 active listings and RFQs →
ASTM A959 347
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A240/A240M S30435 and ASTM A959 347?
ASTM A240/A240M S30435 specifies Cu which is not specified for ASTM A959 347.
Can ASTM A240/A240M S30435 be substituted with ASTM A959 347?
ASTM A240/A240M S30435 and ASTM A959 347 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.