Post Stock Login Register

ASTM A588 vs EN 10025-5 S355J2W

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

ASTM A588 (ASTM A588) and EN 10025-5 S355J2W (EN 10025-5:2019) are both steel grades. Both fall under the Structural Steel (Corten / Weathering) category. ASTM A588 is typically used for used for bridges, railway wagons, transmission poles, architectural structures, containers, and outdoor construction., while EN 10025-5 S355J2W is commonly used for used for bridges, rail wagons, architectural structures, containers, transmission towers, and outdoor steelwork.. ASTM A588 is defined under ASTM International, originating from United States, while EN 10025-5 S355J2W is defined under European Standard (EN), originating from Europe.

As per chemical composition, ASTM A588 vs EN 10025-5 S355J2W is a 76.5% match. As per mechanical properties, the match is 30.2%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With ASTM A588:
CSA G40.21 350A ASTM A588 Grade A AS/NZS 3678 Grade 350WR EN 10025-5 S355J0WP JIS G3114 SMA400 CSA G40.21 260WT EN 10025-5 S355J2WP CSA G40.21 50W ASTM A588 Grade B ASTM A709 Grade HPS 70W CSA G40.21 480A EN 10025-5 S235J2W
Match Breakdown
CHEMISTRY MATCH
76.5%
MECHANICAL MATCH
30.2%
OVERALL
35%
Specifications
Property ASTM A588 EN 10025-5 S355J2W
Standard ASTM A588 EN 10025-5:2019
Category Structural Steel (Corten / Weathering) Structural Steel (Corten / Weathering)
C (%) 0.19 max <=0.16
Mn (%) 0.80-1.25 0.50-1.50
Si (%) 0.30-0.65 <=0.50
Cu (%) 0.20-0.40 0.25-0.55
Cr (%) 0.40-0.70 0.40-0.80
Ni (%) 0.40 max Not specified
P (%) 0.04 max <=0.030
S (%) 0.05 max <=0.030
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A588 EN 10025-5 S355J2W
Tensile Strength 485-630 MPa 470-630 MPa
Yield Strength 345 MPa min >=355 MPa
Elongation 18-21% >=22%
Hardness 140-190 HB Not specified
Condition Not specified Nominal thickness up to 16 mm for yield, 3 to 100 mm for tensile, 3 to 40 mm for elongation (Lo = 5.65 sqrt(S0), longitudinal); transverse values are lower, see blocks
Typical Applications
ASTM A588
Used for bridges, railway wagons, transmission poles, architectural structures, containers, and outdoor construction.
EN 10025-5 S355J2W
Used for bridges, rail wagons, architectural structures, containers, transmission towers, and outdoor steelwork.
Key Differences
Can ASTM A588 Be Substituted With EN 10025-5 S355J2W?
ASTM A588 and EN 10025-5 S355J2W share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
ASTM A588
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2500–2700 mm (98.43–106.3 in)
EN 10025-5 S355J2W
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2900–4400 mm (114.17–173.23 in)
On M-EX Right Now
ASTM A588
2 active listings and RFQs →
EN 10025-5 S355J2W
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A588 and EN 10025-5 S355J2W?
ASTM A588 specifies Ni which is not specified for EN 10025-5 S355J2W.
Can ASTM A588 be substituted with EN 10025-5 S355J2W?
ASTM A588 and EN 10025-5 S355J2W share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.