Post Stock Login Register

ASTM A959 S40975 vs EN 10088-3 X2CrNi12

Strong Match — 92.4% match based on chemical composition and mechanical property overlap.

ASTM A959 S40975 (ASTM A959:2011) and EN 10088-3 X2CrNi12 (EN 10088-3:2014) are both steel grades. Both fall under the Stainless Steel category. ASTM A959 S40975 is typically used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1), while EN 10088-3 X2CrNi12 is commonly used for general purposes, semi-finished products, bars, rods, wire, sections and bright products. ASTM A959 S40975 is defined under ASTM International, originating from United States, while EN 10088-3 X2CrNi12 is defined under European Standard (EN), originating from Europe.

As per chemical composition, ASTM A959 S40975 vs EN 10088-3 X2CrNi12 is a 92.4% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 92.4%.

Frequently Compared With ASTM A959 S40975:
GOST 5632 08X18H10 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr12MoH ASTM A959 .- GOST 5632 06Kh23N28 EN 10088-1 1.4301 GB/T 3280 06Cr19Ni10 EN 10088-1 1.4006 EN 10088-1 1.4401 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr13H IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
92.4%
MECHANICAL MATCH
No shared data
OVERALL
92.4%
Specifications
Property ASTM A959 S40975 EN 10088-3 X2CrNi12
Standard ASTM A959:2011 EN 10088-3:2014
Category Stainless Steel Stainless Steel
C (%) <=0.030 <=0.030
Cr (%) 10.5-11.7 10.5-12.5
Mn (%) <=1.00 <=1.50
N (%) <=0.030 <=0.030
Ni (%) 0.50-1.00 0.30-1.00
P (%) <=0.040 <=0.040
S (%) <=0.030 <=0.030
Si (%) <=1.00 <=1.00
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A959 S40975 EN 10088-3 X2CrNi12
Tensile Strength Not specified 450-600 MPa
Yield Strength Not specified >=260 MPa
Elongation Not specified >=20%
Hardness Not specified <=200 HB
Condition Not specified Annealed (+A), conditions 1C, 1E, 1D, 1X, 1G and 2D, thickness or diameter up to 100 mm; Yield Strength is Rp0.2, Elongation is A (longitudinal), hardness for guidance only
Typical Applications
ASTM A959 S40975
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
EN 10088-3 X2CrNi12
General purposes, semi-finished products, bars, rods, wire, sections and bright products
Can ASTM A959 S40975 Be Substituted With EN 10088-3 X2CrNi12?
ASTM A959 S40975 and EN 10088-3 X2CrNi12 overlap closely enough on chemistry and mechanical properties that EN 10088-3 X2CrNi12 is often considered as a substitute for ASTM A959 S40975 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
On M-EX Right Now
ASTM A959 S40975
0 active listings and RFQs →
EN 10088-3 X2CrNi12
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A959 S40975 and EN 10088-3 X2CrNi12?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can ASTM A959 S40975 be substituted with EN 10088-3 X2CrNi12?
ASTM A959 S40975 and EN 10088-3 X2CrNi12 overlap closely enough on chemistry and mechanical properties that EN 10088-3 X2CrNi12 is often considered as a substitute for ASTM A959 S40975 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.