Post Stock Login Register

ASTM A959 S41428 vs IS 1570 (Part 7) 12Cr12Ni2Mo

Close Alternative — 76.8% match based on chemical composition and mechanical property overlap.

ASTM A959 S41428 (ASTM A959:2011) and IS 1570 (Part 7) 12Cr12Ni2Mo (IS 1570 (Part 7):1992) are both steel grades. Both fall under the Stainless Steel category. ASTM A959 S41428 is typically used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1), while IS 1570 (Part 7) 12Cr12Ni2Mo is commonly used for boilers, pressure vessels, steam turbines, steam and water piping and other power plant equipment working at elevated temperature. ASTM A959 S41428 is defined under ASTM International, originating from United States, while IS 1570 (Part 7) 12Cr12Ni2Mo is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, ASTM A959 S41428 vs IS 1570 (Part 7) 12Cr12Ni2Mo is a 76.8% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 76.8%.

Frequently Compared With ASTM A959 S41428:
IS 1570 (Part 7) 12Cr13H GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4401 IS 1570 (Part 7) 11Cr17Ni13W3TiH ASTM A959 .- GB/T 3280 06Cr19Ni10 EN 10088-1 1.4301 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH
Match Breakdown
CHEMISTRY MATCH
76.8%
MECHANICAL MATCH
No shared data
OVERALL
76.8%
Specifications
Property ASTM A959 S41428 IS 1570 (Part 7) 12Cr12Ni2Mo
Standard ASTM A959:2011 IS 1570 (Part 7):1992
Category Stainless Steel Stainless Steel
Al (%) <=0.025 Not specified
C (%) 0.10-0.17 0.08-0.16
Cr (%) 11.3-12.7 11.0-12.5
Cu (%) <=0.15 Not specified
Mn (%) 0.65-1.05 0.50-0.90
Mo (%) 1.50-2.00 1.5-2.00
N (%) 0.020-0.045 0.02-0.04
Ni (%) 2.3-3.2 2.0-3.0
P (%) <=0.020 <=0.040
S (%) <=0.015 <=0.030
Si (%) 0.10-0.35 <=0.35
Sn (%) <=0.05 Not specified
Ti (%) <=0.05 Not specified
V (%) 0.25-0.40 0.25-0.40
W (%) <=0.10 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property ASTM A959 S41428 IS 1570 (Part 7) 12Cr12Ni2Mo
Tensile Strength Not specified 930-1130 MPa
Yield Strength Not specified >=785 MPa (0.2 % proof stress)
Elongation Not specified >=14%
Condition Not specified Bars, forgings, Q+T, thickness up to 150 (first row of Table 3)
Typical Applications
ASTM A959 S41428
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
IS 1570 (Part 7) 12Cr12Ni2Mo
Boilers, pressure vessels, steam turbines, steam and water piping and other power plant equipment working at elevated temperature
Key Differences
Can ASTM A959 S41428 Be Substituted With IS 1570 (Part 7) 12Cr12Ni2Mo?
ASTM A959 S41428 and IS 1570 (Part 7) 12Cr12Ni2Mo are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
ASTM A959 S41428
0 active listings and RFQs →
IS 1570 (Part 7) 12Cr12Ni2Mo
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A959 S41428 and IS 1570 (Part 7) 12Cr12Ni2Mo?
ASTM A959 S41428 specifies Al, Cu, Sn, Ti which are not specified for IS 1570 (Part 7) 12Cr12Ni2Mo.
Can ASTM A959 S41428 be substituted with IS 1570 (Part 7) 12Cr12Ni2Mo?
ASTM A959 S41428 and IS 1570 (Part 7) 12Cr12Ni2Mo are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.