Post Stock Login Register

DIN EN ISO 4957 1.2344 vs IS 1570 (Part 6) XT35Cr5MoV1

Close Alternative — 83.5% match based on chemical composition and mechanical property overlap.

DIN EN ISO 4957 1.2344 (DIN EN ISO 4957:2018-11) and IS 1570 (Part 6) XT35Cr5MoV1 (IS 1570 (Part 6):1996) are both steel grades. Both fall under the Tool & Die Steels category. DIN EN ISO 4957 1.2344 is defined under European Standard (EN), originating from Europe, while IS 1570 (Part 6) XT35Cr5MoV1 is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, DIN EN ISO 4957 1.2344 vs IS 1570 (Part 6) XT35Cr5MoV1 is a 83.5% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 83.5%.

Frequently Compared With DIN EN ISO 4957 1.2344:
GB/T 1299 4Cr5MoSiV EN ISO 683-17 100Cr6 GB/T 1299 4Cr5MoSiV1 GOST 5950 4H5MFS AISI 52100 IS 1570 (Part 6) 133T3 IS 1570 (Part 6) 55T8 IS 1570 (Part 6) 50T8 IS 1570 (Part 6) 75T6 IS 1570 (Part 6) 70T6 IS 1570 (Part 6) 60T6 IS 1570 (Part 6) 65T6
Match Breakdown
CHEMISTRY MATCH
83.5%
MECHANICAL MATCH
No shared data
OVERALL
83.5%
Specifications
Property DIN EN ISO 4957 1.2344 IS 1570 (Part 6) XT35Cr5MoV1
Standard DIN EN ISO 4957:2018-11 IS 1570 (Part 6):1996
Category Tool & Die Steels Tool & Die Steels
C (%) 0.37–0.43 0.30-0.40
Mn (%) 0.30–0.50 0.25-0.50
Si (%) 0.90–1.20 0.80-1.20
Cr (%) 4.80–5.50 4.75-5.50
Mo (%) 1.20–1.50 1.20-1.60
V (%) 0.90–1.10 1.00-1.20
S (%) ≤0.030 <=0.035
P (%) ≤0.030 <=0.035
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property DIN EN ISO 4957 1.2344 IS 1570 (Part 6) XT35Cr5MoV1
Hardness (annealed) ≤229 HB Not specified
Hardness (hardened) 44–52 HRC Not specified
Tensile Strength 1200–1600 MPa Not specified
Elongation ≥8% Not specified
Typical Applications
DIN EN ISO 4957 1.2344
Die casting dies, extrusion dies, forging dies, hot shear blades, mandrels, pressure die casting tooling
IS 1570 (Part 6) XT35Cr5MoV1
Not documented
Can DIN EN ISO 4957 1.2344 Be Substituted With IS 1570 (Part 6) XT35Cr5MoV1?
DIN EN ISO 4957 1.2344 and IS 1570 (Part 6) XT35Cr5MoV1 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
DIN EN ISO 4957 1.2344
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 3000–3700 mm (118.11–145.67 in)
IS 1570 (Part 6) XT35Cr5MoV1
No active listings currently.
On M-EX Right Now
DIN EN ISO 4957 1.2344
2 active listings and RFQs →
IS 1570 (Part 6) XT35Cr5MoV1
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between DIN EN ISO 4957 1.2344 and IS 1570 (Part 6) XT35Cr5MoV1?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can DIN EN ISO 4957 1.2344 be substituted with IS 1570 (Part 6) XT35Cr5MoV1?
DIN EN ISO 4957 1.2344 and IS 1570 (Part 6) XT35Cr5MoV1 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.