Post Stock Login Register

EN 10025-2 E335 vs SAE J403 1002

Related Material — 65% match based on chemical composition and mechanical property overlap.

EN 10025-2 E335 (EN 10025-2:2019) and SAE J403 1002 (SAE J403:2014) are both steel grades. EN 10025-2 E335 is classified under Structural Steel, while SAE J403 1002 is classified under Carbon Steel — a different category, which is worth noting alongside the chemistry match below. EN 10025-2 E335 is typically used for hot rolled products of structural steels, while SAE J403 1002 is commonly used for chemistry-only grade; product scope as listed in the composition notes. EN 10025-2 E335 is defined under European Standard (EN), originating from Europe, while SAE J403 1002 is defined under SAE International, originating from United States.

As per chemical composition, EN 10025-2 E335 vs SAE J403 1002 is a 87.2% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 65%.

Frequently Compared With EN 10025-2 E335:
GOST 19281 09G2S CSA G40.21 260W AS/NZS 3679.1 300 AS/NZS 3679.1 350 CSA G40.21 400W CSA G40.21 480W ASTM A1008 SS Grade 80 ASTM A572 Gr.65
Other Structural Steel Grades to Compare With EN 10025-2 E335:
CSA G40.21 300W CSA G40.21 350W CSA G40.21 400A ASTM A1008 SS Grade 50
Match Breakdown
CHEMISTRY MATCH
87.2%
MECHANICAL MATCH
No shared data
OVERALL
65%
Specifications
Property EN 10025-2 E335 SAE J403 1002
Standard EN 10025-2:2019 SAE J403:2014
Category Structural Steel Carbon Steel
P (%) <=0.045 <=0.030 (flat rolled), <=0.040 (long products)
S (%) <=0.045 <=0.035 (flat rolled), <=0.050 (long products)
N (%) <=0.012 Not specified
C (%) Not specified 0.02-0.04
Mn (%) Not specified <=0.35
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10025-2 E335 SAE J403 1002
Tensile Strength 570-710 MPa Not specified
Yield Strength >=335 MPa Not specified
Elongation >=16% Not specified
Condition Nominal thickness up to 16 mm (tensile for 3 to 100 mm, elongation for 3 to 40 mm), longitudinal test pieces Not specified
Typical Applications
EN 10025-2 E335
Hot rolled products of structural steels
SAE J403 1002
Chemistry-only grade; product scope as listed in the composition notes
Key Differences
Can EN 10025-2 E335 Be Substituted With SAE J403 1002?
EN 10025-2 E335 and SAE J403 1002 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
EN 10025-2 E335
0 active listings and RFQs →
SAE J403 1002
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10025-2 E335 and SAE J403 1002?
Different category: EN 10025-2 E335 is Structural Steel, SAE J403 1002 is Carbon Steel. EN 10025-2 E335 specifies N which is not specified for SAE J403 1002. SAE J403 1002 specifies C, Mn which are not specified for EN 10025-2 E335.
Can EN 10025-2 E335 be substituted with SAE J403 1002?
EN 10025-2 E335 and SAE J403 1002 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.