Post Stock Login Register

EN 10025-5 S235J0W vs EN 10088-1 X30MnCrN16-14

Related Material — 62.1% match based on chemical composition and mechanical property overlap.

EN 10025-5 S235J0W (EN 10025-5:2019) and EN 10088-1 X30MnCrN16-14 (EN 10088-1:2023) are both steel grades. EN 10025-5 S235J0W is classified under Structural Steel (Corten / Weathering), while EN 10088-1 X30MnCrN16-14 is classified under Stainless Steel — a different category, which is worth noting alongside the chemistry match below. EN 10025-5 S235J0W is defined under European Standard (EN), originating from Europe, while EN 10088-1 X30MnCrN16-14 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10025-5 S235J0W vs EN 10088-1 X30MnCrN16-14 is a 62.1% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 62.1%.

Frequently Compared With EN 10025-5 S235J0W:
EN 10025-5 S355K2W EN 10025-5 S420K2W EN 10025-5 S460J2W CSA G40.21 260WT CSA G40.21 480A ASTM A588 ASTM A588 Grade A ASTM A588 Grade B ASTM A709 Grade HPS 70W AS/NZS 3678 Grade 350WR EN 10025-5 S235J2W EN 10025-5 S355J0W
Match Breakdown
CHEMISTRY MATCH
62.1%
MECHANICAL MATCH
No shared data
OVERALL
62.1%
Specifications
Property EN 10025-5 S235J0W EN 10088-1 X30MnCrN16-14
Standard EN 10025-5:2019 EN 10088-1:2023
Category Structural Steel (Corten / Weathering) Stainless Steel
C (%) <=0.13 0.20-0.40
Si (%) <=0.40 <=1.00
Mn (%) 0.20-0.60 14.0-18.0
P (%) <=0.035 <=0.045
S (%) <=0.035 <=0.015
N (%) <=0.012 0.20-0.40
Cr (%) 0.40-0.80 12.0-16.0
Cu (%) 0.25-0.55 <=2.00
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10025-5 S235J0W EN 10088-1 X30MnCrN16-14
Tensile Strength 360-510 MPa Not specified
Yield Strength >=235 MPa Not specified
Elongation >=26% Not specified
Condition Nominal thickness up to 16 mm for yield, 3 to 100 mm for tensile, 3 to 40 mm for elongation (Lo = 5.65 sqrt(S0), longitudinal); transverse values are lower, see blocks Not specified
Key Differences
Can EN 10025-5 S235J0W Be Substituted With EN 10088-1 X30MnCrN16-14?
EN 10025-5 S235J0W and EN 10088-1 X30MnCrN16-14 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
EN 10025-5 S235J0W
0 active listings and RFQs →
EN 10088-1 X30MnCrN16-14
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10025-5 S235J0W and EN 10088-1 X30MnCrN16-14?
Different category: EN 10025-5 S235J0W is Structural Steel (Corten / Weathering), EN 10088-1 X30MnCrN16-14 is Stainless Steel.
Can EN 10025-5 S235J0W be substituted with EN 10088-1 X30MnCrN16-14?
EN 10025-5 S235J0W and EN 10088-1 X30MnCrN16-14 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.