Post Stock Login Register

EN 10025-5 S460J2W vs AS/NZS 3678 Grade 350WR

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

EN 10025-5 S460J2W (EN 10025-5:2019) and AS/NZS 3678 Grade 350WR (AS/NZS 3678:2016) are both steel grades. Both fall under the Structural Steel (Corten / Weathering) category. EN 10025-5 S460J2W is defined under European Standard (EN), originating from Europe, while AS/NZS 3678 Grade 350WR is defined under Australian/New Zealand Standard (AS/NZS), originating from Australia/New Zealand.

As per chemical composition, EN 10025-5 S460J2W vs AS/NZS 3678 Grade 350WR is a 88.1% match. As per mechanical properties, the match is 13%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With EN 10025-5 S460J2W:
EN 10025-5 S420K2W CSA G40.21 350A CSA G40.21 480A ASTM A588 EN 10025-5 S235J0W EN 10025-5 S420J5W EN 10025-5 S460J0W EN 10025-5 S460J4W EN 10025-5 S460J5W CSA G40.21 260WT CSA G40.21 50W ASTM A588 Grade B
Match Breakdown
CHEMISTRY MATCH
88.1%
MECHANICAL MATCH
13%
OVERALL
35%
Specifications
Property EN 10025-5 S460J2W AS/NZS 3678 Grade 350WR
Standard EN 10025-5:2019 AS/NZS 3678:2016
Category Structural Steel (Corten / Weathering) Structural Steel (Corten / Weathering)
C (%) <=0.20 <=0.20
Si (%) <=0.65 <=0.50
Mn (%) <=1.40 <=1.70
P (%) <=0.030 <=0.035
S (%) <=0.030 <=0.035
N (%) <=0.025 Not specified
Cr (%) 0.40-0.80 0.40-0.80
Cu (%) 0.25-0.55 0.25-0.55
Ni (%) Not specified <=0.65
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10025-5 S460J2W AS/NZS 3678 Grade 350WR
Tensile Strength 530-710 MPa 480-620 MPa
Yield Strength >=460 MPa 350 MPa min
Elongation >=17% 20% min
Condition Nominal thickness up to 16 mm for yield, 3 to 100 mm for tensile, 3 to 40 mm for elongation (Lo = 5.65 sqrt(S0), longitudinal); transverse values are lower, see blocks Not specified
Typical Applications
EN 10025-5 S460J2W
Not documented
AS/NZS 3678 Grade 350WR
Weather-resistant (corrosion-resistant) structural steel; exposed bridge and structural applications requiring atmospheric corrosion resistance
Key Differences
Can EN 10025-5 S460J2W Be Substituted With AS/NZS 3678 Grade 350WR?
EN 10025-5 S460J2W and AS/NZS 3678 Grade 350WR share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN 10025-5 S460J2W
No active listings currently.
AS/NZS 3678 Grade 350WR
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2500–2800 mm (98.43–110.24 in)
On M-EX Right Now
EN 10025-5 S460J2W
0 active listings and RFQs →
AS/NZS 3678 Grade 350WR
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10025-5 S460J2W and AS/NZS 3678 Grade 350WR?
EN 10025-5 S460J2W specifies N which is not specified for AS/NZS 3678 Grade 350WR. AS/NZS 3678 Grade 350WR specifies Ni which is not specified for EN 10025-5 S460J2W.
Can EN 10025-5 S460J2W be substituted with AS/NZS 3678 Grade 350WR?
EN 10025-5 S460J2W and AS/NZS 3678 Grade 350WR share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.