Post Stock Login Register

EN 10028-2 X10CrMoVNb9-1 vs EN 10088-1 X11CrMoWVNb9-1-1

Related Material — 65% match based on chemical composition and mechanical property overlap.

EN 10028-2 X10CrMoVNb9-1 (EN 10028-2:2017) and EN 10088-1 X11CrMoWVNb9-1-1 (EN 10088-1:2014) are both steel grades. EN 10028-2 X10CrMoVNb9-1 is classified under Alloy Steel, while EN 10088-1 X11CrMoWVNb9-1-1 is classified under Stainless Steel — a different category, which is worth noting alongside the chemistry match below. EN 10028-2 X10CrMoVNb9-1 is defined under European Standard (EN), originating from Europe, while EN 10088-1 X11CrMoWVNb9-1-1 is defined under European Standard (EN), originating from Europe.

As per chemical composition, EN 10028-2 X10CrMoVNb9-1 vs EN 10088-1 X11CrMoWVNb9-1-1 is a 67.3% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 65%.

Frequently Compared With EN 10028-2 X10CrMoVNb9-1:
UNI 11234 100Cr6 IS 1570 (Part 4) 10Cr20Mo6 IS 4367 10Cr9Mo10 EN 10028-2 12CrMo9-10 EN 10028-2 12CrMoV12-10 IS 4367 07Cr4Mo6 IS 1570 (Part 4) 07Cr4Mo6 NF A35-565 100C6 IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 103Cr6 IS 1570 (Part 4) 105Cr5 IS 1570 (Part 7) 10Cr36Mo10H
Match Breakdown
CHEMISTRY MATCH
67.3%
MECHANICAL MATCH
No shared data
OVERALL
65%
Specifications
Property EN 10028-2 X10CrMoVNb9-1 EN 10088-1 X11CrMoWVNb9-1-1
Standard EN 10028-2:2017 EN 10088-1:2014
Category Alloy Steel Stainless Steel
C (%) 0.08-0.12 0.09-0.13
Si (%) <=0.50 0.10-0.50
Mn (%) 0.30-0.60 0.30-0.60
P (%) <=0.020 <=0.020
S (%) <=0.005 <=0.010
Al (%) <=0.040 <=0.040
N (%) 0.030-0.070 0.050-0.090
Cr (%) 8.00-9.50 8.5-9.5
Cu (%) <=0.30 Not specified
Mo (%) 0.85-1.05 0.90-1.10
Nb (%) 0.06-0.10 0.060-0.10
Ni (%) <=0.30 0.10-0.40
V (%) 0.18-0.25 0.18-0.25
W (%) Not specified 0.90-1.10
B (%) Not specified 0.0005-0.0050
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10028-2 X10CrMoVNb9-1 EN 10088-1 X11CrMoWVNb9-1-1
Tensile Strength 580-760 MPa Not specified
Yield Strength >=445 MPa Not specified
Elongation >=18% Not specified
Condition Usual delivery condition normalized and tempered (+NT), nominal thickness up to 60 mm; transverse direction, Yield Strength is ReH, Elongation is A Not specified
Typical Applications
EN 10028-2 X10CrMoVNb9-1
Flat products for pressure purposes
EN 10088-1 X11CrMoWVNb9-1-1
Not documented
Key Differences
Can EN 10028-2 X10CrMoVNb9-1 Be Substituted With EN 10088-1 X11CrMoWVNb9-1-1?
EN 10028-2 X10CrMoVNb9-1 and EN 10088-1 X11CrMoWVNb9-1-1 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
EN 10028-2 X10CrMoVNb9-1
0 active listings and RFQs →
EN 10088-1 X11CrMoWVNb9-1-1
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10028-2 X10CrMoVNb9-1 and EN 10088-1 X11CrMoWVNb9-1-1?
Different category: EN 10028-2 X10CrMoVNb9-1 is Alloy Steel, EN 10088-1 X11CrMoWVNb9-1-1 is Stainless Steel. EN 10028-2 X10CrMoVNb9-1 specifies Cu which is not specified for EN 10088-1 X11CrMoWVNb9-1-1. EN 10088-1 X11CrMoWVNb9-1-1 specifies W, B which are not specified for EN 10028-2 X10CrMoVNb9-1.
Can EN 10028-2 X10CrMoVNb9-1 be substituted with EN 10088-1 X11CrMoWVNb9-1-1?
EN 10028-2 X10CrMoVNb9-1 and EN 10088-1 X11CrMoWVNb9-1-1 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.