Post Stock Login Register

EN 10028-3 P275NL2 vs IS 1570 (Part 7) Fe410H

Related Material — 65% match based on chemical composition and mechanical property overlap.

EN 10028-3 P275NL2 (EN 10028-3:2017) and IS 1570 (Part 7) Fe410H (IS 1570 (Part 7):1992) are both steel grades. EN 10028-3 P275NL2 is classified under Alloy Steel, while IS 1570 (Part 7) Fe410H is classified under Carbon Steel — a different category, which is worth noting alongside the chemistry match below. EN 10028-3 P275NL2 is typically used for flat products for pressure equipment, while IS 1570 (Part 7) Fe410H is commonly used for boilers, pressure vessels, steam turbines, steam and water piping and other power plant equipment working at elevated temperature. EN 10028-3 P275NL2 is defined under European Standard (EN), originating from Europe, while IS 1570 (Part 7) Fe410H is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, EN 10028-3 P275NL2 vs IS 1570 (Part 7) Fe410H is a 76.1% match. As per mechanical properties, the match is 59%. Combined, this makes them a related material overall at 65%.

Frequently Compared With EN 10028-3 P275NL2:
IS 1570 (Part 4) 10Mo6 UNI 11234 100Cr6 IS 1570 (Part 4) 103Cr6 IS 1570 (Part 4) 105Cr5 IS 1570 (Part 7) 10Cr36Mo10H IS 1570 (Part 7) 10Mo6H IS 4367 07Cr4Mo6 IS 1570 (Part 4) 07Cr4Mo6 NF A35-565 100C6 IS 1570 (Part 4) 103Cr4 IS 1570 (Part 4) 10Cr20Mo6 IS 4367 10Cr9Mo10
Match Breakdown
CHEMISTRY MATCH
76.1%
MECHANICAL MATCH
59%
OVERALL
65%
Specifications
Property EN 10028-3 P275NL2 IS 1570 (Part 7) Fe410H
Standard EN 10028-3:2017 IS 1570 (Part 7):1992
Category Alloy Steel Carbon Steel
C (%) <=0.16 <=0.20
Si (%) <=0.40 0.10-0.35
Mn (%) 0.80-1.50 0.50-1.30
P (%) <=0.020 <=0.03
S (%) <=0.005 <=0.03
Al (%) >=0.020 Not specified
N (%) <=0.012 Not specified
Cr (%) <=0.30 <=0.25
Cu (%) <=0.30 <=0.30
Mo (%) <=0.08 <=0.10
Nb (%) <=0.05 Not specified
Ni (%) <=0.50 <=0.30
Ti (%) <=0.03 Not specified
V (%) <=0.05 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10028-3 P275NL2 IS 1570 (Part 7) Fe410H
Tensile Strength 390-510 MPa 410-520 MPa
Yield Strength >=275 MPa >=225 MPa (0.2 % proof stress)
Elongation >=24% >=24%
Condition Normalized, nominal thickness up to 16 mm Plate, quadrangular seamless pipe, N, thickness over 3 to 16 (first row of Table 3)
Typical Applications
EN 10028-3 P275NL2
Flat products for pressure equipment
IS 1570 (Part 7) Fe410H
Boilers, pressure vessels, steam turbines, steam and water piping and other power plant equipment working at elevated temperature
Key Differences
Can EN 10028-3 P275NL2 Be Substituted With IS 1570 (Part 7) Fe410H?
EN 10028-3 P275NL2 and IS 1570 (Part 7) Fe410H share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
EN 10028-3 P275NL2
0 active listings and RFQs →
IS 1570 (Part 7) Fe410H
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10028-3 P275NL2 and IS 1570 (Part 7) Fe410H?
Different category: EN 10028-3 P275NL2 is Alloy Steel, IS 1570 (Part 7) Fe410H is Carbon Steel. EN 10028-3 P275NL2 specifies Al, N, Nb, Ti which are not specified for IS 1570 (Part 7) Fe410H.
Can EN 10028-3 P275NL2 be substituted with IS 1570 (Part 7) Fe410H?
EN 10028-3 P275NL2 and IS 1570 (Part 7) Fe410H share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.