Post Stock Login Register

EN 10088-1 X4CrNiMo16-5 vs AISI 52100

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

EN 10088-1 X4CrNiMo16-5 (EN 10088-1:2014) and AISI 52100 are both steel grades. Both fall under the Tool & Die Steels category. EN 10088-1 X4CrNiMo16-5 is typically used for plastic injection moulds, die casting dies for zinc/aluminium, while AISI 52100 is commonly used for anti-friction bearings, ball screws, precision rollers. EN 10088-1 X4CrNiMo16-5 is defined under European Standard (EN), originating from Europe, while AISI 52100 is defined under AISI, originating from United States.

As per chemical composition, EN 10088-1 X4CrNiMo16-5 vs AISI 52100 is a 56.8% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With EN 10088-1 X4CrNiMo16-5:
EN ISO 4957 1.2316 DIN EN ISO 4957 1.2344 EN ISO 683-17 100Cr6 GOST 5950 4H5MFS1 GB/T 1299 4Cr5MoSiV DIN EN ISO 4957 1.2379 GB/T 1299 4Cr5MoSiV1 GOST 5950 4H5MFS GOST 5950 3H2W8F GB/T 1299 3Cr2W8V IS 3748 103T3 IS 1570 (Part 6) 103T3
Match Breakdown
CHEMISTRY MATCH
56.8%
MECHANICAL MATCH
0%
OVERALL
35%
Specifications
Property EN 10088-1 X4CrNiMo16-5 AISI 52100
Standard EN 10088-1:2014 AISI
Category Tool & Die Steels Tool & Die Steels
C (%) ≤0.06 0.93–1.05
Si (%) ≤0.70 0.15–0.35
Mn (%) ≤1.50 0.25–0.45
Cr (%) 15.0–17.0 1.35–1.60
Mo (%) 0.80–1.50 Not specified
Ni (%) 3.50–5.50 Not specified
S (%) Not specified ≤0.025
P (%) Not specified ≤0.025
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X4CrNiMo16-5 AISI 52100
Hardness HRC 28–34 (delivered) 60–66 (hardened)
Hardness HRC (hardened) 38–42 Not specified
Corrosion Resistance Good Not specified
Tensile Strength Not specified ≥620 MPa (annealed)
Hardness HB Not specified 179–229 (annealed)
Typical Applications
EN 10088-1 X4CrNiMo16-5
Plastic injection moulds, die casting dies for zinc/aluminium
AISI 52100
Anti-friction bearings, ball screws, precision rollers
Key Differences
Can EN 10088-1 X4CrNiMo16-5 Be Substituted With AISI 52100?
EN 10088-1 X4CrNiMo16-5 and AISI 52100 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN 10088-1 X4CrNiMo16-5
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 3700–4000 mm (145.67–157.48 in)
AISI 52100
Round Bar → (3 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 3000–3200 mm (118.11–125.98 in)
On M-EX Right Now
EN 10088-1 X4CrNiMo16-5
2 active listings and RFQs →
AISI 52100
3 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X4CrNiMo16-5 and AISI 52100?
EN 10088-1 X4CrNiMo16-5 specifies Mo, Ni which are not specified for AISI 52100. AISI 52100 specifies S, P which are not specified for EN 10088-1 X4CrNiMo16-5.
Can EN 10088-1 X4CrNiMo16-5 be substituted with AISI 52100?
EN 10088-1 X4CrNiMo16-5 and AISI 52100 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.