Post Stock Login Register

EN 10088-1 X4CrNiMo16-5 vs IS 1570 (Part 6) 103T3

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

EN 10088-1 X4CrNiMo16-5 (EN 10088-1:2014) and IS 1570 (Part 6) 103T3 (IS 1570 (Part 6):1996) are both steel grades. Both fall under the Tool & Die Steels category. EN 10088-1 X4CrNiMo16-5 is defined under European Standard (EN), originating from Europe, while IS 1570 (Part 6) 103T3 is defined under Bureau of Indian Standards (IS), originating from India.

As per chemical composition, EN 10088-1 X4CrNiMo16-5 vs IS 1570 (Part 6) 103T3 is a 53.6% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With EN 10088-1 X4CrNiMo16-5:
EN ISO 4957 1.2316 DIN EN ISO 4957 1.2344 EN ISO 683-17 100Cr6 GB/T 1299 4Cr5MoSiV GOST 5950 4H5MFS1 DIN EN ISO 4957 1.2379 GB/T 1299 4Cr5MoSiV1 GOST 5950 4H5MFS AISI 52100 GOST 5950 3H2W8F GB/T 1299 3Cr2W8V IS 3748 103T3
Match Breakdown
CHEMISTRY MATCH
53.6%
MECHANICAL MATCH
No shared data
OVERALL
35%
Specifications
Property EN 10088-1 X4CrNiMo16-5 IS 1570 (Part 6) 103T3
Standard EN 10088-1:2014 IS 1570 (Part 6):1996
Category Tool & Die Steels Tool & Die Steels
C (%) ≤0.06 0.95-1.10
Si (%) ≤0.70 0.10-0.30
Mn (%) ≤1.50 <=0.40
Cr (%) 15.0–17.0 <=0.20
Mo (%) 0.80–1.50 Not specified
Ni (%) 3.50–5.50 <=0.25
P (%) Not specified <=0.035
S (%) Not specified <=0.035
Cu (%) Not specified <=0.25
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X4CrNiMo16-5 IS 1570 (Part 6) 103T3
Hardness HRC 28–34 (delivered) Not specified
Hardness HRC (hardened) 38–42 Not specified
Corrosion Resistance Good Not specified
Typical Applications
EN 10088-1 X4CrNiMo16-5
Plastic injection moulds, die casting dies for zinc/aluminium
IS 1570 (Part 6) 103T3
Not documented
Key Differences
Can EN 10088-1 X4CrNiMo16-5 Be Substituted With IS 1570 (Part 6) 103T3?
EN 10088-1 X4CrNiMo16-5 and IS 1570 (Part 6) 103T3 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN 10088-1 X4CrNiMo16-5
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 3700–4000 mm (145.67–157.48 in)
IS 1570 (Part 6) 103T3
No active listings currently.
On M-EX Right Now
EN 10088-1 X4CrNiMo16-5
2 active listings and RFQs →
IS 1570 (Part 6) 103T3
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X4CrNiMo16-5 and IS 1570 (Part 6) 103T3?
EN 10088-1 X4CrNiMo16-5 specifies Mo which is not specified for IS 1570 (Part 6) 103T3. IS 1570 (Part 6) 103T3 specifies P, S, Cu which are not specified for EN 10088-1 X4CrNiMo16-5.
Can EN 10088-1 X4CrNiMo16-5 be substituted with IS 1570 (Part 6) 103T3?
EN 10088-1 X4CrNiMo16-5 and IS 1570 (Part 6) 103T3 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.