Post Stock Login Register

EN 10088-1 X4CrNiMo16-5 vs ASTM A959 XM-25

Related Material — 65% match based on chemical composition and mechanical property overlap.

EN 10088-1 X4CrNiMo16-5 (EN 10088-1:2014) and ASTM A959 XM-25 (ASTM A959:2011) are both steel grades. EN 10088-1 X4CrNiMo16-5 is classified under Tool & Die Steels, while ASTM A959 XM-25 is classified under Stainless Steel — a different category, which is worth noting alongside the chemistry match below. EN 10088-1 X4CrNiMo16-5 is typically used for plastic injection moulds, die casting dies for zinc/aluminium, while ASTM A959 XM-25 is commonly used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1). EN 10088-1 X4CrNiMo16-5 is defined under European Standard (EN), originating from Europe, while ASTM A959 XM-25 is defined under ASTM International, originating from United States.

As per chemical composition, EN 10088-1 X4CrNiMo16-5 vs ASTM A959 XM-25 is a 67.4% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 65%.

Frequently Compared With EN 10088-1 X4CrNiMo16-5:
EN ISO 4957 1.2316 DIN EN ISO 4957 1.2344 EN ISO 683-17 100Cr6 GOST 5950 4H5MFS1 GB/T 1299 4Cr5MoSiV DIN EN ISO 4957 1.2379 GB/T 1299 4Cr5MoSiV1 GOST 5950 4H5MFS AISI 52100 GOST 5950 3H2W8F GB/T 1299 3Cr2W8V IS 3748 103T3
Match Breakdown
CHEMISTRY MATCH
67.4%
MECHANICAL MATCH
No shared data
OVERALL
65%
Specifications
Property EN 10088-1 X4CrNiMo16-5 ASTM A959 XM-25
Standard EN 10088-1:2014 ASTM A959:2011
Category Tool & Die Steels Stainless Steel
C (%) ≤0.06 <=0.05
Si (%) ≤0.70 <=1.00
Mn (%) ≤1.50 <=1.00
Cr (%) 15.0–17.0 14.0-16.0
Mo (%) 0.80–1.50 0.50-1.00
Ni (%) 3.50–5.50 5.0-7.0
Cu (%) Not specified 1.25-1.75
P (%) Not specified <=0.040
S (%) Not specified <=0.030
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10088-1 X4CrNiMo16-5 ASTM A959 XM-25
Hardness HRC 28–34 (delivered) Not specified
Hardness HRC (hardened) 38–42 Not specified
Corrosion Resistance Good Not specified
Typical Applications
EN 10088-1 X4CrNiMo16-5
Plastic injection moulds, die casting dies for zinc/aluminium
ASTM A959 XM-25
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
Key Differences
Can EN 10088-1 X4CrNiMo16-5 Be Substituted With ASTM A959 XM-25?
EN 10088-1 X4CrNiMo16-5 and ASTM A959 XM-25 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN 10088-1 X4CrNiMo16-5
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 3700–4000 mm (145.67–157.48 in)
ASTM A959 XM-25
No active listings currently.
On M-EX Right Now
EN 10088-1 X4CrNiMo16-5
2 active listings and RFQs →
ASTM A959 XM-25
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10088-1 X4CrNiMo16-5 and ASTM A959 XM-25?
Different category: EN 10088-1 X4CrNiMo16-5 is Tool & Die Steels, ASTM A959 XM-25 is Stainless Steel. ASTM A959 XM-25 specifies Cu, P, S which are not specified for EN 10088-1 X4CrNiMo16-5.
Can EN 10088-1 X4CrNiMo16-5 be substituted with ASTM A959 XM-25?
EN 10088-1 X4CrNiMo16-5 and ASTM A959 XM-25 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.