Post Stock Login Register

IS 1570 (Part 6) T90V2 vs DIN EN ISO 4957 1.2344

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

IS 1570 (Part 6) T90V2 (IS 1570 (Part 6):1996) and DIN EN ISO 4957 1.2344 (DIN EN ISO 4957:2018-11) are both steel grades. Both fall under the Tool & Die Steels category. IS 1570 (Part 6) T90V2 is defined under Bureau of Indian Standards (IS), originating from India, while DIN EN ISO 4957 1.2344 is defined under European Standard (EN), originating from Europe.

As per chemical composition, IS 1570 (Part 6) T90V2 vs DIN EN ISO 4957 1.2344 is a 58.9% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With IS 1570 (Part 6) T90V2:
GOST 5950 4H5MFS EN ISO 4957 1.2316 EN ISO 683-17 100Cr6 IS 1570 (Part 6) 103T3 GB/T 1299 4Cr5MoSiV1 GOST 5950 4H5MFS1 DIN EN ISO 4957 1.2379 GB/T 1299 3Cr2W8V GOST 5950 3H2W8F GB/T 1299 4Cr5MoSiV IS 1570 (Part 6) 133T3 IS 1570 (Part 6) 70T3
Match Breakdown
CHEMISTRY MATCH
58.9%
MECHANICAL MATCH
No shared data
OVERALL
35%
Specifications
Property IS 1570 (Part 6) T90V2 DIN EN ISO 4957 1.2344
Standard IS 1570 (Part 6):1996 DIN EN ISO 4957:2018-11
Category Tool & Die Steels Tool & Die Steels
C (%) 0.85-0.95 0.37–0.43
Si (%) 0.10-0.35 0.90–1.20
Mn (%) <=0.40 0.30–0.50
V (%) 0.15-0.30 0.90–1.10
P (%) <=0.035 ≤0.030
S (%) <=0.035 ≤0.030
Cr (%) Not specified 4.80–5.50
Mo (%) Not specified 1.20–1.50
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 1570 (Part 6) T90V2 DIN EN ISO 4957 1.2344
Hardness (annealed) Not specified ≤229 HB
Hardness (hardened) Not specified 44–52 HRC
Tensile Strength Not specified 1200–1600 MPa
Elongation Not specified ≥8%
Typical Applications
IS 1570 (Part 6) T90V2
Not documented
DIN EN ISO 4957 1.2344
Die casting dies, extrusion dies, forging dies, hot shear blades, mandrels, pressure die casting tooling
Key Differences
Can IS 1570 (Part 6) T90V2 Be Substituted With DIN EN ISO 4957 1.2344?
IS 1570 (Part 6) T90V2 and DIN EN ISO 4957 1.2344 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
IS 1570 (Part 6) T90V2
No active listings currently.
DIN EN ISO 4957 1.2344
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 3000–3700 mm (118.11–145.67 in)
On M-EX Right Now
IS 1570 (Part 6) T90V2
0 active listings and RFQs →
DIN EN ISO 4957 1.2344
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 1570 (Part 6) T90V2 and DIN EN ISO 4957 1.2344?
DIN EN ISO 4957 1.2344 specifies Cr, Mo which are not specified for IS 1570 (Part 6) T90V2.
Can IS 1570 (Part 6) T90V2 be substituted with DIN EN ISO 4957 1.2344?
IS 1570 (Part 6) T90V2 and DIN EN ISO 4957 1.2344 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.