Post Stock Login Register

IS 2062 E165 vs EN 10025-2 S275

Close Alternative — 73.3% match based on chemical composition and mechanical property overlap.

IS 2062 E165 (IS 2062:2006) and EN 10025-2 S275 (EN 10025-2:2019) are both steel grades. Both fall under the Structural Steel category. IS 2062 E165 is typically used for structural work: welded, bolted and riveted structures and general engineering purposes, while EN 10025-2 S275 is commonly used for structural beams, columns, bridges, general fabrication. IS 2062 E165 is defined under Bureau of Indian Standards (IS), originating from India, while EN 10025-2 S275 is defined under European Standard (EN), originating from Europe.

As per chemical composition, IS 2062 E165 vs EN 10025-2 S275 is a 93.3% match. As per mechanical properties, the match is 33.3%. Combined, this makes them a close alternative overall at 73.3%.

Frequently Compared With IS 2062 E165:
IS 2062 E250A IS 2062 E250A IS 2062 E250B IS 2062 E250BR CSA G40.21 260W CSA G40.21 400A IS 2062 E250B0 IS 2062 E250A GOST 19281 09G2S AS/NZS 3679.1 300 CSA G40.21 300W AS/NZS 3679.1 350
Match Breakdown
CHEMISTRY MATCH
93.3%
MECHANICAL MATCH
33.3%
OVERALL
73.3%
Specifications
Property IS 2062 E165 EN 10025-2 S275
Standard IS 2062:2006 EN 10025-2:2019
Category Structural Steel Structural Steel
C (%) <=0.25 0-0.25
Mn (%) <=1.25 0-1.5
S (%) <=0.045 max 0.04
P (%) <=0.045 max 0.04
Si (%) Not specified 0-0.5
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 2062 E165 EN 10025-2 S275
Tensile Strength >=290 MPa 410-560 MPa
Yield Strength 165 MPa (all thicknesses) 275 MPa min (t<=16mm)
Elongation >=23% 23% min
Impact not required Not specified
Typical Applications
IS 2062 E165
Structural work: welded, bolted and riveted structures and general engineering purposes
EN 10025-2 S275
Structural beams, columns, bridges, general fabrication
Key Differences
Can IS 2062 E165 Be Substituted With EN 10025-2 S275?
IS 2062 E165 and EN 10025-2 S275 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
IS 2062 E165
No active listings currently.
EN 10025-2 S275
Round Bar → (2 listings)
Diameter: 40–40 mm (1.57–1.57 in)
Length: 5000–5000 mm (196.85–196.85 in)
On M-EX Right Now
IS 2062 E165
0 active listings and RFQs →
EN 10025-2 S275
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 2062 E165 and EN 10025-2 S275?
EN 10025-2 S275 specifies Si which is not specified for IS 2062 E165.
Can IS 2062 E165 be substituted with EN 10025-2 S275?
IS 2062 E165 and EN 10025-2 S275 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.