Post Stock Login Register

IS 2062 E410A vs AS/NZS 3679.1 350

Close Alternative — 76.2% match based on chemical composition and mechanical property overlap.

IS 2062 E410A (IS 2062:2011) and AS/NZS 3679.1 350 (AS/NZS 3679.1:2016) are both steel grades. Both fall under the Structural Steel category. IS 2062 E410A is typically used for high strength structural applications, while AS/NZS 3679.1 350 is commonly used for hot-rolled structural bars and sections for primary structural beams, columns, and framing. IS 2062 E410A is defined under Bureau of Indian Standards (IS), originating from India, while AS/NZS 3679.1 350 is defined under Australian/New Zealand Standard (AS/NZS), originating from Australia/New Zealand.

As per chemical composition, IS 2062 E410A vs AS/NZS 3679.1 350 is a 97.7% match. As per mechanical properties, the match is 33.3%. Combined, this makes them a close alternative overall at 76.2%.

Frequently Compared With IS 2062 E410A:
CSA G40.21 400W CSA G40.21 350W CSA G40.21 260W CSA G40.21 300W GOST 19281 09G2S AS/NZS 3679.1 300 CSA G40.21 400A IS 2062 E250B0 CSA G40.21 480W IS 2062 E250A ASTM A1008 SS Grade 50 ASTM A1008 SS Grade 80
Match Breakdown
CHEMISTRY MATCH
97.7%
MECHANICAL MATCH
33.3%
OVERALL
76.2%
Specifications
Property IS 2062 E410A AS/NZS 3679.1 350
Standard IS 2062:2011 AS/NZS 3679.1:2016
Category Structural Steel Structural Steel
C (%) <=0.20 <=0.22
Mn (%) <=1.60 <=1.70
Si (%) <=0.45 <=0.50
S (%) <=0.045 <=0.040
P (%) <=0.045 <=0.040
CEV (%) <=0.50 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 2062 E410A AS/NZS 3679.1 350
Tensile Strength >=540 MPa 480-640 MPa
Yield Strength 410 MPa (<=20mm) / 390 MPa (20-40mm) / 380 MPa (>40mm) 350 MPa min
Elongation >=20% 20% min
Impact not required Not specified
Typical Applications
IS 2062 E410A
High strength structural applications
AS/NZS 3679.1 350
Hot-rolled structural bars and sections for primary structural beams, columns, and framing
Key Differences
Can IS 2062 E410A Be Substituted With AS/NZS 3679.1 350?
IS 2062 E410A and AS/NZS 3679.1 350 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
IS 2062 E410A
Plate → (8 listings)
Thickness: 8–10 mm (0.31–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2500–4100 mm (98.43–161.42 in)
Angle → (6 listings)
Leg 1: 50–130 mm (1.97–5.12 in)
Leg 2: 130–6000 mm (5.12–236.22 in)
Thickness: 6–8 mm (0.24–0.31 in)
AS/NZS 3679.1 350
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2900–3200 mm (114.17–125.98 in)
On M-EX Right Now
IS 2062 E410A
14 active listings and RFQs →
AS/NZS 3679.1 350
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 2062 E410A and AS/NZS 3679.1 350?
IS 2062 E410A specifies CEV which is not specified for AS/NZS 3679.1 350.
Can IS 2062 E410A be substituted with AS/NZS 3679.1 350?
IS 2062 E410A and AS/NZS 3679.1 350 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.