Post Stock Login Register

JIS G4303 SUS304 vs EN 10088-1 X2CrNi18-9

Close Alternative — 77.6% match based on chemical composition and mechanical property overlap.

JIS G4303 SUS304 (JIS G4303:2021) and EN 10088-1 X2CrNi18-9 (EN 10088-1:2023) are both steel grades. Both fall under the Stainless Steel category. JIS G4303 SUS304 is defined under Japanese Industrial Standards (JIS), originating from Japan, while EN 10088-1 X2CrNi18-9 is defined under European Standard (EN), originating from Europe.

As per chemical composition, JIS G4303 SUS304 vs EN 10088-1 X2CrNi18-9 is a 77.6% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 77.6%.

Frequently Compared With JIS G4303 SUS304:
EN 10088-1 1.4301 EN 10088-1 1.4845 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 GB/T 3280 06Cr19Ni10 EN 10088-1 1.4401 GOST 5632 12Kh13 IS 1570 (Part 7) 12Cr12MoH ASTM A959 .- IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoVH
Match Breakdown
CHEMISTRY MATCH
77.6%
MECHANICAL MATCH
No shared data
OVERALL
77.6%
Specifications
Property JIS G4303 SUS304 EN 10088-1 X2CrNi18-9
Standard JIS G4303:2021 EN 10088-1:2023
Category Stainless Steel Stainless Steel
C (%) ≤0.08 <=0.030
Si (%) ≤1.00 <=1.00
Mn (%) ≤2.00 <=2.00
Cr (%) 18.0–20.0 17.5-19.5
Ni (%) 8.0–10.5 8.0-10.5
P (%) ≤0.045 <=0.045
S (%) ≤0.030 <=0.015
N (%) Not specified <=0.10
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property JIS G4303 SUS304 EN 10088-1 X2CrNi18-9
Tensile Strength ≥520 MPa Not specified
Yield Strength ≥205 MPa Not specified
Elongation ≥40% Not specified
Hardness ≤187 HB Not specified
Typical Applications
JIS G4303 SUS304
Food equipment, chemical vessels, architectural applications
EN 10088-1 X2CrNi18-9
Not documented
Key Differences
Can JIS G4303 SUS304 Be Substituted With EN 10088-1 X2CrNi18-9?
JIS G4303 SUS304 and EN 10088-1 X2CrNi18-9 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
JIS G4303 SUS304
Sheet → (3 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2500–4000 mm (98.43–157.48 in)
EN 10088-1 X2CrNi18-9
No active listings currently.
On M-EX Right Now
JIS G4303 SUS304
3 active listings and RFQs →
EN 10088-1 X2CrNi18-9
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between JIS G4303 SUS304 and EN 10088-1 X2CrNi18-9?
EN 10088-1 X2CrNi18-9 specifies N which is not specified for JIS G4303 SUS304.
Can JIS G4303 SUS304 be substituted with EN 10088-1 X2CrNi18-9?
JIS G4303 SUS304 and EN 10088-1 X2CrNi18-9 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.