Post Stock Login Register

UNS C51000 vs UNS C63000

Minimal Match — 31.3% match based on chemical composition and mechanical property overlap.

UNS C51000 and UNS C63000 are both bronze grades. Both fall under the Bronze Alloys category. UNS C51000 is defined under Unified Numbering System (UNS), originating from United States, while UNS C63000 is defined under Unified Numbering System (UNS), originating from United States.

As per chemical composition, UNS C51000 vs UNS C63000 is a 38.3% match. As per mechanical properties, the match is 17.3%. Combined, this makes them a minimal match overall at 31.3%.

Frequently Compared With UNS C51000:
UNS C52100 UNS C95400 UNS C93200 UNS C90300 UNS C61300 UNS C65500
Match Breakdown
CHEMISTRY MATCH
38.3%
MECHANICAL MATCH
17.3%
OVERALL
31.3%
Specifications
Property UNS C51000 UNS C63000
Standard UNS UNS
Category Bronze Alloys Bronze Alloys
Cu (%) balance balance
Pb (%) 0-0.05 Not specified
Sn (%) 4.20-5.80 0-0.20
Zn (%) 0-0.30 0-0.30
Fe (%) 0-0.10 4.00-5.50
P (%) 0.03-0.35 Not specified
Ni (%) Not specified 2.00-4.00
Al (%) Not specified 9.00-11.00
Mn (%) Not specified 0-1.50
Si (%) Not specified 0-0.25
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property UNS C51000 UNS C63000
Yield Strength ~275-350 MPa (H04 hard) ~345-520 MPa (M30/HR50)
Tensile Strength ~415-485 MPa (H04 hard) ~620-815 MPa (M30/HR50)
Elongation ~15-25% (H04 hard) ~15-20% (M30/HR50)
Note Phosphor bronze 5% Sn, values for H04 hard temper Aluminium bronze, values for as-extruded/hot-rolled condition
Key Differences
Can UNS C51000 Be Substituted With UNS C63000?
UNS C51000 and UNS C63000 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
UNS C51000
Sheet → (6 listings)
Thickness: 0.5–1.5 mm (0.02–0.06 in)
Width: 600–600 mm (23.62–23.62 in)
Length: 1200–1200 mm (47.24–47.24 in)
UNS C63000
No active listings currently.
On M-EX Right Now
UNS C51000
6 active listings and RFQs →
UNS C63000
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between UNS C51000 and UNS C63000?
UNS C51000 specifies Pb, P which are not specified for UNS C63000. UNS C63000 specifies Ni, Al, Mn, Si which are not specified for UNS C51000.
Can UNS C51000 be substituted with UNS C63000?
UNS C51000 and UNS C63000 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.