Post Stock Login Register

UNS C51000 vs UNS C95400

Minimal Match — 25.5% match based on chemical composition and mechanical property overlap.

UNS C51000 and UNS C95400 are both bronze grades. Both fall under the Bronze Alloys category. UNS C51000 is defined under Unified Numbering System (UNS), originating from United States, while UNS C95400 is defined under Unified Numbering System (UNS), originating from United States.

As per chemical composition, UNS C51000 vs UNS C95400 is a 26.9% match. As per mechanical properties, the match is 22.8%. Combined, this makes them a minimal match overall at 25.5%.

Frequently Compared With UNS C51000:
UNS C52100 UNS C93200 UNS C90300 UNS C61300 UNS C63000 UNS C65500
Match Breakdown
CHEMISTRY MATCH
26.9%
MECHANICAL MATCH
22.8%
OVERALL
25.5%
Specifications
Property UNS C51000 UNS C95400
Standard UNS UNS
Category Bronze Alloys Bronze Alloys
Cu (%) balance 83.00 min
Pb (%) 0-0.05 Not specified
Sn (%) 4.20-5.80 Not specified
Zn (%) 0-0.30 Not specified
Fe (%) 0-0.10 3.00-5.00
P (%) 0.03-0.35 Not specified
Ni (%) Not specified 0-1.50
Al (%) Not specified 10.00-11.50
Mn (%) Not specified 0-0.50
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property UNS C51000 UNS C95400
Yield Strength ~275-350 MPa (H04 hard) ~240-360 MPa (as cast)
Tensile Strength ~415-485 MPa (H04 hard) ~600-710 MPa (as cast)
Elongation ~15-25% (H04 hard) ~8-16% (as cast)
Note Phosphor bronze 5% Sn, values for H04 hard temper Aluminium bronze casting alloy, indicative as-cast values
Key Differences
Can UNS C51000 Be Substituted With UNS C95400?
UNS C51000 and UNS C95400 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
UNS C51000
Sheet → (6 listings)
Thickness: 0.5–1.5 mm (0.02–0.06 in)
Width: 600–600 mm (23.62–23.62 in)
Length: 1200–1200 mm (47.24–47.24 in)
UNS C95400
Round Bar → (2 listings)
Diameter: 80–80 mm (3.15–3.15 in)
Length: 1000–1000 mm (39.37–39.37 in)
On M-EX Right Now
UNS C51000
6 active listings and RFQs →
UNS C95400
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between UNS C51000 and UNS C95400?
UNS C51000 specifies Pb, Sn, Zn, P which are not specified for UNS C95400. UNS C95400 specifies Ni, Al, Mn which are not specified for UNS C51000.
Can UNS C51000 be substituted with UNS C95400?
UNS C51000 and UNS C95400 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.