Post Stock Login Register

ASTM A959 S41428 vs ASTM A959 XM-32

Close Alternative — 76% match based on chemical composition and mechanical property overlap.

ASTM A959 S41428 (ASTM A959:2011) and ASTM A959 XM-32 (ASTM A959:2011) are both steel grades. Both fall under the Stainless Steel category. ASTM A959 S41428 is typically used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1), while ASTM A959 XM-32 is commonly used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1). ASTM A959 S41428 is defined under ASTM International, originating from United States, while ASTM A959 XM-32 is defined under ASTM International, originating from United States.

As per chemical composition, ASTM A959 S41428 vs ASTM A959 XM-32 is a 76% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 76%.

Frequently Compared With ASTM A959 S41428:
IS 1570 (Part 7) 12Cr12Ni2Mo GOST 5632 06Kh23N28 EN 10088-1 1.4401 IS 1570 (Part 7) 12Cr13H ASTM A959 .- GB/T 3280 06Cr19Ni10 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4301 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH
Match Breakdown
CHEMISTRY MATCH
76%
MECHANICAL MATCH
No shared data
OVERALL
76%
Specifications
Property ASTM A959 S41428 ASTM A959 XM-32
Standard ASTM A959:2011 ASTM A959:2011
Category Stainless Steel Stainless Steel
Al (%) <=0.025 Not specified
C (%) 0.10-0.17 0.08-0.15
Cr (%) 11.3-12.7 11.0-12.5
Cu (%) <=0.15 Not specified
Mn (%) 0.65-1.05 0.50-0.90
Mo (%) 1.50-2.00 1.50-2.00
N (%) 0.020-0.045 0.01-0.05
Ni (%) 2.3-3.2 2.00-3.00
P (%) <=0.020 <=0.025
S (%) <=0.015 <=0.025
Si (%) 0.10-0.35 <=0.35
Sn (%) <=0.05 Not specified
Ti (%) <=0.05 Not specified
V (%) 0.25-0.40 0.25-0.40
W (%) <=0.10 Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Typical Applications
ASTM A959 S41428
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
ASTM A959 XM-32
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
Key Differences
Can ASTM A959 S41428 Be Substituted With ASTM A959 XM-32?
ASTM A959 S41428 and ASTM A959 XM-32 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
ASTM A959 S41428
0 active listings and RFQs →
ASTM A959 XM-32
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between ASTM A959 S41428 and ASTM A959 XM-32?
ASTM A959 S41428 specifies Al, Cu, Sn, Ti which are not specified for ASTM A959 XM-32.
Can ASTM A959 S41428 be substituted with ASTM A959 XM-32?
ASTM A959 S41428 and ASTM A959 XM-32 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.