Post Stock Login Register

EN 10025-2 E360 vs AS/NZS 3679.1 350

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

EN 10025-2 E360 (EN 10025-2:2019) and AS/NZS 3679.1 350 (AS/NZS 3679.1:2016) are both steel grades. Both fall under the Structural Steel category. EN 10025-2 E360 is typically used for hot rolled products of structural steels, while AS/NZS 3679.1 350 is commonly used for hot-rolled structural bars and sections for primary structural beams, columns, and framing. EN 10025-2 E360 is defined under European Standard (EN), originating from Europe, while AS/NZS 3679.1 350 is defined under Australian/New Zealand Standard (AS/NZS), originating from Australia/New Zealand.

As per chemical composition, EN 10025-2 E360 vs AS/NZS 3679.1 350 is a 79.9% match. As per mechanical properties, the match is 0%. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With EN 10025-2 E360:
GOST 19281 09G2S CSA G40.21 260W CSA G40.21 300W CSA G40.21 350W CSA G40.21 400W CSA G40.21 480W ASTM A1008 SS Grade 50 ASTM A1008 SS Grade 80 ASTM A283C
Other Structural Steel Grades to Compare With EN 10025-2 E360:
AS/NZS 3679.1 300 CSA G40.21 400A ASTM A572 Gr.65
Match Breakdown
CHEMISTRY MATCH
79.9%
MECHANICAL MATCH
0%
OVERALL
35%
Specifications
Property EN 10025-2 E360 AS/NZS 3679.1 350
Standard EN 10025-2:2019 AS/NZS 3679.1:2016
Category Structural Steel Structural Steel
P (%) <=0.045 <=0.040
S (%) <=0.045 <=0.040
N (%) <=0.012 Not specified
C (%) Not specified <=0.22
Mn (%) Not specified <=1.70
Si (%) Not specified <=0.50
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10025-2 E360 AS/NZS 3679.1 350
Tensile Strength 670-830 MPa 480-640 MPa
Yield Strength >=360 MPa 350 MPa min
Elongation >=11% 20% min
Condition Nominal thickness up to 16 mm (tensile for 3 to 100 mm, elongation for 3 to 40 mm), longitudinal test pieces Not specified
Typical Applications
EN 10025-2 E360
Hot rolled products of structural steels
AS/NZS 3679.1 350
Hot-rolled structural bars and sections for primary structural beams, columns, and framing
Key Differences
Can EN 10025-2 E360 Be Substituted With AS/NZS 3679.1 350?
EN 10025-2 E360 and AS/NZS 3679.1 350 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN 10025-2 E360
No active listings currently.
AS/NZS 3679.1 350
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2900–3200 mm (114.17–125.98 in)
On M-EX Right Now
EN 10025-2 E360
0 active listings and RFQs →
AS/NZS 3679.1 350
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10025-2 E360 and AS/NZS 3679.1 350?
EN 10025-2 E360 specifies N which is not specified for AS/NZS 3679.1 350. AS/NZS 3679.1 350 specifies C, Mn, Si which are not specified for EN 10025-2 E360.
Can EN 10025-2 E360 be substituted with AS/NZS 3679.1 350?
EN 10025-2 E360 and AS/NZS 3679.1 350 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.