Post Stock Login Register

EN 10025-2 S250 vs AS/NZS 3679.1 300

Close Alternative — 72% match based on chemical composition and mechanical property overlap.

EN 10025-2 S250 (EN 10025-2:2019) and AS/NZS 3679.1 300 (AS/NZS 3679.1:2016) are both steel grades. Both fall under the Structural Steel category. EN 10025-2 S250 is typically used for used for fabricated structures, beams, support frames, machinery bases, towers, and construction components., while AS/NZS 3679.1 300 is commonly used for hot-rolled structural bars and sections for general structural framing. EN 10025-2 S250 is defined under European Standard (EN), originating from Europe, while AS/NZS 3679.1 300 is defined under Australian/New Zealand Standard (AS/NZS), originating from Australia/New Zealand.

As per chemical composition, EN 10025-2 S250 vs AS/NZS 3679.1 300 is a 97.4% match. As per mechanical properties, the match is 21.1%. Combined, this makes them a close alternative overall at 72%.

Frequently Compared With EN 10025-2 S250:
CSA G40.21 260W ASTM A283C CSA G40.21 400W CSA G40.21 480W CSA G40.21 300W CSA G40.21 400A ASTM A1008 SS Grade 80 GOST 19281 09G2S ASTM A572 Grade 50 ASTM A1008 SS Grade 50 AS/NZS 3679.1 350 CSA G40.21 350W
Match Breakdown
CHEMISTRY MATCH
97.4%
MECHANICAL MATCH
21.1%
OVERALL
72%
Specifications
Property EN 10025-2 S250 AS/NZS 3679.1 300
Standard EN 10025-2:2019 AS/NZS 3679.1:2016
Category Structural Steel Structural Steel
C (%) 0.20 max <=0.22
Mn (%) 1.50 max <=1.70
Si (%) 0.40 max <=0.50
P (%) 0.040 max <=0.040
S (%) 0.040 max <=0.040
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10025-2 S250 AS/NZS 3679.1 300
Tensile Strength 410-560 MPa 440-600 MPa
Yield Strength 250 MPa min 300 MPa min
Elongation 22-25% 22% min
Hardness 120-170 HB Not specified
Typical Applications
EN 10025-2 S250
Used for fabricated structures, beams, support frames, machinery bases, towers, and construction components.
AS/NZS 3679.1 300
Hot-rolled structural bars and sections for general structural framing
Can EN 10025-2 S250 Be Substituted With AS/NZS 3679.1 300?
EN 10025-2 S250 and AS/NZS 3679.1 300 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
EN 10025-2 S250
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 3300–3500 mm (129.92–137.8 in)
AS/NZS 3679.1 300
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2700–2700 mm (106.3–106.3 in)
On M-EX Right Now
EN 10025-2 S250
2 active listings and RFQs →
AS/NZS 3679.1 300
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10025-2 S250 and AS/NZS 3679.1 300?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can EN 10025-2 S250 be substituted with AS/NZS 3679.1 300?
EN 10025-2 S250 and AS/NZS 3679.1 300 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.